Mitsubishi Galant 9G. Manual — part 435
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-8
NOTE: Since the TCL is controlled with the same ABS/TCL-ECU used to control the ABS, the codes (with a
*) used only for the ABS also appear.
The inspection contents for the codes (with a *) used only for the ABS do not described in this group.
C1226*
ABS front right solenoid inlet valve
-
C1231*
ABS front right solenoid outlet valve
-
C1236*
ABS front left solenoid valve inlet valve
-
C1241*
ABS front left solenoid valve outlet valve
-
C1246*
ABS rear right solenoid valve inlet valve
-
C1251*
ABS rear right solenoid valve outlet valve
-
C1256*
ABS rear left solenoid valve inlet valve
-
C1261*
ABS rear left solenoid valve outlet valve
-
C1266*
ABS hydraulic unit motor stuck
-
C1273*
ABS hydraulic unit motor drive circuit stuck off
-
C1274*
ABS hydraulic unit motor drive circuit stuck on
-
C1278*
ABS solenoid valve power circuit stuck off
-
C1279*
ABS solenoid valve power circuit stuck on
-
C1395*
Brake fluid filling incompleted
-
C1396
Engine torque intervention refusal
C1397
Transmission range switch failure
C1607
ABS/TCL-ECU failure
GROUP 35B, ABS
Diagnosis
−
Diagnostic Trouble
Code Procedures
C
C1860
ABS/TCL-ECU power supply
Abnormal rise in voltage
GROUP 35B, ABS
Diagnosis
−
Diagnostic Trouble
Code Procedures
C
C1861
ABS/TCL-ECU power supply
Abnormal drop in voltage
GROUP 35B, ABS
Diagnosis
−
Diagnostic Trouble
Code Procedures
C
U1073
CAN communications system bus off
GROUP 35B, ABS
Diagnosis
−
Diagnostic Trouble
Code Procedures
U
U1100
CAN communications system time out error engine related data
U1101
CAN communications system time out error A/T related data
U1120
CAN communications system TCL uncontrollable by engine
malfunction
U1400
Dynamic range error APS1
DTC
INSPECTION ITEM
DIAGNOSTIC CONTENT
REFERENCE PAGE
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-9
DIAGNOSTIC TROUBLE CODE PROCEDURES
C1396 Engine Torque Intervention Refusal
CAUTION
• If DTC C1396 is set in the ABS/TCL-ECU,
always diagnose the CAN main bus line. If
there is any fault in the CAN bus lines, an
incorrect DTC may be set.
• Whenever the ABS/TCL-ECU is replaced,
ensure that the communication circuit is nor-
mal.
.
DTC SET CONDITIONS
This DTC is set when the refusal of torque interven-
tion request is sent from PCM.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CODE TO BE
SET ARE:)
• Malfunction of the MFI system.
• Malfunction of the CAN bus line.
• Malfunction of the ABS/TCL-ECU.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for MFI system diagnostic trouble code. (Refer to
GROUP 13B, MFI Diagnosis
− Diagnostic Function − How
to Read and Erase Diagnostic Trouble Code
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Repair the MFI control system. (Refer to GROUP
13B, MFI Diagnosis
− Diagnostic Trouble Code Chart
NO : Go to Step 2.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-10
STEP 2. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line. (Refer to
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is any DTC set?
YES : Repair the CAN bus line. (Refer to GROUP 54C,
Diagnosis
− Can Bus Diagnostic Chart
Then go to Step 4.
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Use scan tool MB991958 to read the TCL diagnostic trouble
).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is DTC C1396 set?
YES : Replace the hydraulic unit (integrated with
ABS/TCL-ECU). (Refer to GROUP 35B
− Hydraulic
Unit
NO : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-11
STEP 4. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Use scan tool MB991958 to read the TCL diagnostic trouble
).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is DTC C1396 set?
YES : Return to Step 1.
NO : The procedure is complete.
C1397 Transmission Range Switch Failure
CAUTION
• If DTC C1397 is set in the ABS/TCL-ECU,
always diagnose the CAN main bus line. If
there is any fault in the CAN bus lines, an
incorrect DTC may be set.
• Whenever the ABS/TCL-ECU is replaced,
ensure that the communication circuit is nor-
mal.
• The A/T system-related DTC may be set when
DTC C1397 is set. (For details refer to GROUP
00, Intersystem Affiliated DTC Reference
Table
). Diagnose the A/T system first
when the A/T system-related DTC is set.
.
DTC SET CONDITIONS
This DTC is set when the transmission range switch
fail request is sent from PCM.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CODE TO BE
SET ARE:)
• Malfunction of the A/T system.
• Malfunction of the ABS/TCL-ECU.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст