Mitsubishi Galant 9G. Manual — part 1542
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-40
7. Choose "Key registration" from "Special Function" screen.
8. Enter the vehicle’s password (secret code) on the "Key
registration" screen, and then click the check mark icon.
Follow the prompts on the screen to insert key(s) into the
ignition switch to begin key registration.
9. If the key ID was registered successfully, "Progress"
indication will turn active (gray). Then the registration
process completes. If the key ID failed to be registered,
"In-Complete" indication will turn active (gray).
10.The number of keys currently registered will be displayed.
To register an additional key, replace the ignition key with
the next key to be registered within five seconds. Key ID
registration screen will be displayed, then register another
key.
NOTE: A maximum of eight different keys can be registered.
11.This completes the registration operation. Turn the ignition
switch "LOCK" (OFF) and leave it off for approximately ten
seconds.
12.Check that the engine can be started with each of the
ignition keys.
13.Check that the immobilizer system DTC and MFI system
DTC did not set.
14.If not DTC is shown, terminate the scan tool MB991958.
15.Turn the ignition switch to "LOCK" (OFF) position.
16.Disconnect scan tool MB991958.
.
Key registration
Transponder ID
addition
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC207299
AE
POWERTRAIN
IMMOBILIZER
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Back
Space
Space
Clear
Clear
Key registration
ey registration
AC207300
AC
POWERTRAIN
IMMOBILIZER
Special Function
IMMOBILIZER-ECU registration
IMMOBILIZER-ECU registration
Progress
Progress
In-Complete
In-Complete
Key registration
ey registration
AC207302
AC
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-41
REGISTRATION OF ADDITIONAL KEYS WITH THE
SCAN TOOL
Additional key(s) can be registered with the scan tool while
keeping all existing key data.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool MB991958.
NOTE: To register additional keys with the scan tool, no regis-
tered keys must be lost.
1. Connect scan tool MB991958 to the 16-pin data link
connector.
2. Turn the ignition switch to "ON" position.
NOTE: Before registration, check that no DTC code is set. If
a DTC code is set, resolve the problem beforehand.
3. Carry out steps 3 to 6 of the sub-section "Registration with
scan tool."
4. Choose "Transponder ID addition" from "Special Function"
screen.
5. Enter the vehicles password (secret code) on the
"Transponder ID addition" screen, and then click the check
mark icon.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Key registration
Transponder ID
addition
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC207299
AF
key registration
Transponder ID
addition
POWERTRAIN
IMMOBILIZER
Password
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Back
Space
Space
Clear
Clear
Trasponder ID addition
rasponder ID addition
AC207301
AC
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-42
6. If an additional registration is made successfully, the screen
will ask if another key is registered or not. If the third ignition
key is registered, remove the key, which has been
registered. Then insert the third key within five seconds, and
then turn it to the ON position.
7. Register the additional ignition key according to step 6
above. The number of the registered ignition keys are
shown on "The number of registered key" screen.
NOTE: A maximum of eight different keys can be registered.
8. This completes the registration operation. Turn the ignition
switch "LOCK" (OFF) and leave it off for approximately ten
seconds.
9. Check that the engine can be started with each of the
ignition keys.
10.Check that the immobilizer system DTC and MFI system
DTC did not set.
11.If not DTC is shown, terminate the scan tool MB991958.
12.Turn the ignition switch to "LOCK" (OFF) position.
13.Disconnect scan tool MB991958.
.
AC207301
AC209775
POWERTRAIN
IMMOBILIZER
Key ID register
ey ID register
The number of registered key
The number of registered key
3
Progre
Progre
Special Function
Trasponder ID addition
rasponder ID addition
About Additional T
About Additional Transponder
ransponder
ID SET
ID SET
If register another key ID, press the
If register another key ID, press the
OK button after inserting a new key
OK button after inserting a new key
within 5 sec and turning on IG-SW
within 5 sec and turning on IG-SW.
AD
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-43
REGISTRATION OF ADDITIONAL KEY(S)
WITHOUT USING THE SCAN TOOL
If the scan tool is not available, new key(s) can be registered by
operating two keys which have been registered to the vehicle
(A maximum of eight keys can be registered to one vehicle).
Follow the procedure below to register new key(s) to the vehi-
cle.
NOTE: The registered key is the key that allows you to start the
engine.
1. Turn "ON" the ignition switch by using the first registered key
(key A), and wait for five seconds.
2. Remove the first registered key (key A).
3. Insert the second registered ignition key (key B), and turn it
to the ON position.
4. After approximately 10 seconds the immobilizer indicator will
start blinking, and then additional registration mode is
entered.
5. Check the immobilizer indicator starts blinking, and then
remove the second registered key (key B).
6. Insert the third ignition key, and turn it to the ON position.
7. The immobilizer-ECU identifies the new key to accept or
reject it, and operates the immobilizer indicator (See the
table below).
8. If a new ignition key is registered further, repeat steps 1 to 7
above.
A maximum of eight ignition keys can be registered to one vehi-
cle (If you attempt to register the ninth key, the immobi-
lizer-ECU rejects the key). If any of the following conditions are
satisfied, the additional key registration mode will terminate:
• The immobilizer indicator starts blinking for more than 30
seconds.
• After the ignition key has been turned to the "LOCK" (OFF),
the engine control relay is turned off.
• The scan tool has started communicating with vehicle sys-
tems.
9. After the registration mode has terminated, the additionally
registered key(s) should allow you to start the engine.
The new key is:
Registration is:
Immobilizer indicator:
Operation
Timing
Not registered yet
Accepted
Illuminates for
three seconds
In approximately three seconds after
the ignition key(s) have been
registered
Already registered
Rejected
Illuminates for
three seconds
In approximately three seconds after
the ECU judges that the keys have
been registered
Read error
Rejected
Extinguished
After the ECU detects a read error
AC307460
AB
IMMOBILIZER INDICATOR LIGHT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст