Mitsubishi Galant 9G. Manual — part 1114
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-756
.
CIRCUIT OPERATION
• The PCM (terminal 21) supplies a 5-volt refer-
ence signal to the fuel tank differential pressure
sensor (terminal 3). The fuel tank differential
pressure sensor (terminal 2) is grounded through
the PCM (terminal 22).
• The fuel tank differential pressure sensor (termi-
nal 1) returns a voltage signal to the PCM (termi-
nal 23) that is proportional to the pressure in the
fuel tank.
.
TECHNICAL DESCRIPTION
• The PCM monitors the fuel tank differential pres-
sure sensor output voltage.
• The PCM determines whether the fuel tank differ-
ential pressure sensor signal voltage is within
normal operating parameters.
.
DESCRIPTIONS OF MONITOR METHODS
• Compare purge solenoid status with fuel tank dif-
ferential pressure sensor output voltage.
.
MONITOR EXECUTION
• Continuous.
.
MONITOR EXECUTION CONDITIONS
(OTHER MONITOR AND SENSOR)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Evaporative emission purge solenoid monitor
• Evaporative emission ventilation solenoid monitor
Sensor (The sensors below are determined to be
normal)
• Mass airflow sensor
• Barometric pressure sensor
• Intake air temperature sensor
• Engine coolant temperature sensor
• Accelerator pedal position sensor
.
AC305266
CONNECTOR: D-23
AB
D-23 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-757
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS
Check Conditions
• 2 seconds or more have passed since the start-
ing sequence was completed.
Judgment Criteria
• The fuel tank differential pressure sensor output
voltage remains 0.2 volt or less for 5 seconds.
.
OBD-ll DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-ll Drive Cycle −
Procedure 1
− Evaporative Emission System Leak
.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CODE TO BE
SET ARE:)
• Malfunction of the fuel tank differential pressure
sensor.
• A damaged harness in the fuel tank differential
pressure sensor circuit.
• Malfunction of the PCM.
.
AC401447
RANGE CHECK - MIN. / MAX.
NO
YES
CONTINUOUS
FAILURE FOR 5 SECS
START
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
MONITORING
CONDITIONS
OUTPUT VOLTAGE
< 1.0V
OUTPUT VOLTAGE
> 4.8V
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-758
OVERVIEW OF TROUBLESHOOTING
• DTC P0452 can be set by a faulty fuel tank differ-
ential pressure sensor or related circuit, or PCM
failure.
• To check for system blockage, do a performance
test which uses a mechanical vacuum gauge and
scan tool MB991958 set on the fuel tank differen-
tial pressure sensor (TANK PRS SNSR 73). The
mechanical gauge reading is used to verify scan
tool MB991958 reading. A comparison of the
mechanical gauge with the reading on scan tool
MB991958 will locate a problem in the system.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
• MB991658: Test Harness Set
• MB991923: Power Plant ECU Check Harness
STEP 1. Using scan tool MB991958, check data list item 73:
Fuel Tank Differential Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Disconnect hose H from the evaporative emission canister,
and plug the hose.
(3) Turn the ignition switch to the "ON" position.
(4) Remove the fuel cap.
(5) Set scan tool MB991958 to the data reading mode.
• Item 73, Fuel Tank Differential Pressure Sensor.
• The fuel tank pressure reading on the scan tool
should be
−1.5 to 1.5 kPa (−0.443 to 0.443 inHg).
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC306778
AC
HOSE H
PLUG
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-759
(6) Connect the evaporative emission system pressure pump
(Miller number 6872A) to the fuel tank filler tube by using
fuel tank adapter (MLR-8382) and pressurize the fuel tank.
• The fuel tank pressure reading should increase.
(7) Turn the ignition switch to the "LOCK" (OFF) position. Then
disconnect scan tool MB991958.
(8) Remove the evaporative emission system pressure pump
(Miller number 6872A) and the fuel tank adapter
(MLR-8382), and reinstall the fuel cap.
(9) Connect hose H to the evaporative emission canister.
Q: Is the fuel tank pressure between
−1.5 and 1.5 kPa
(
−0.443 and 0.443 inHg)?
YES : It can be assumed that this malfunction is intermittent
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
). Go to
Step 17.
NO : Go to Step 2.
AC306661
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст