Mitsubishi Galant 9G. Manual — part 35
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-136
ETACS-
ECU
JUNCTION BLOCK
FRONT POWER
WINDOW
SUB SWITCH
KEY
REMINDER
SWITCH
POWER
WINDOW
MAIN SWITCH
FRONT DOOR
SWITCH
(LH)
FRONT DOOR
SWITCH
(RH)
REAR DOOR
SWITCH
(LH)
REAR DOOR
SWITCH
(RH)
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-137
INSPECTION PROCEDURE C-1: Central Door Locking System: The Central Door Locking System
does not Work at all.
NOTE: This troubleshooting procedure requires the
use of scan tool MB991958 and SWS monitor kit
MB991813. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
JUNCTION
BLOCK
ETACS-
ECU
FUSIBLE
LINK
1
JUNCTION
BLOCK SIDE
FRONT DOOR
LOCK ACTUATOR
(LH)
UNLOCK
RELAY
LOCK
RELAY
Central Door Lock Power Supply Circuit
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-138
.
CIRCUIT OPERATION
• The ETACS-ECU controls the central door lock
system, locking or unlocking all the doors by acti-
vating the central door lock relay (built into the
ETACS-ECU). The ETACS-ECU uses inputs from
the following components:
• Front door lock actuator
• Front door lock key cylinder switch
• Door lock switch, which is incorporated in the
power window main switch or front power win-
dow sub switch
.
TROUBLESHOOTING HINTS
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
• The ETACS-ECU may be defective
AC305015AD
FUSIBLE LINK (1)
AC305231AJ
CONNECOTRS: C-26, C-29
C-29
C-26
AC305415
C-211
CONNECTORS: C-211, C-216
C-216 (B)
AF
JUNCTION BLOCK
(FRONT VIEW)
AC305413
C-219
C-217
CONNECTORS: C-217, C-219
AF
JUNCTION BLOCK
(REAR VIEW)
AC305262
E-15 (B)
CONNECTOR: E-15
AM
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-139
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
• MB991813: SWS Monitor Kit
• MB991806: SWS Monitor Cartridge
• MB991812: SWS Monitor Harness (For Column-ECU)
• MB991822: Probe Harness
STEP 1. Use scan tool MB991958 to select "ECU COMM
Check" on the SWS monitor display.
Check the ETACS-ECU.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958. Connect
special tool MB991910 before connecting special tool
MB991812. Be sure to connect special tool MB991806 after
turning on special tool MB991824.
(1) Connect the special tool. Refer to "How to connect SWS
."
(2) Turn the ignition switch to the "LOCK" (OFF) position.
(3) Operate scan tool MB991958 according to the procedure
below to display "ECU COMM Check."
a. Select "Interactive Diagnosis."
b. Select "System Select."
c. Select "SWS."
d. Select "SWS MONITOR."
e. Select "ECU COMM Check."
(4) MUT-III should show "OK" on the "ECU COMM Check"
menu for the "ETACS ECU" menu.
Q: Is "OK" displayed for the "ETACS ECU" menu?
YES : Go to Step 2.
NO : Refer to Inspection Procedure A-3 "Communication
with the ETACS-ECU is not possible
."
AC305411AB
MB991910
DATA LINK
CONNECTOR
MB991827
MB991824
MB991806
MB991812
AC302210
COLUMN SWITCH
CONNECTOR
COLUMN SWITCH
CONNECTOR AT
HARNESS SIDE
MB991812
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст