Mitsubishi Galant 9G. Manual — part 367
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-14
AC306938
83 ± 12 N·m
61 ± 9 ft-lb
180 ± 20 N·m
133 ± 15 ft-lb
180 ± 20 N·m
133 ± 15 ft-lb
165 ± 15 N·m*²
122 ± 11 ft-lb*²
65 ± 6 N·m
48 ± 4 ft-lb
29 ± 4 N·m
21 ± 3 ft-lb
AB
58 ± 7 N·m
43 ± 5 ft-lb
165 ± 15 N·m
122 ± 11 ft-lb
18 ± 2 N·m
13 ± 2 ft-lb
83 ± 12 N·m
61 ± 9 ft-lb
58 ± 7 N·m
43 ± 5 ft-lb
48 ± 7 N·m
36 ± 5 ft-lb
83 ± 12 N·m
61 ± 9 ft-lb
15
20
16
19
21
N
12 ± 2 N·m
102 ± 22 in-lb
58 ± 7 N·m*¹
43 ± 5 ft-lb*¹
58 ± 7 N·m*¹
43 ± 5 ft-lb*¹
58 ± 7 N·m
43 ± 5 ft-lb
7
12 ± 2 N·m
102 ± 22 in-lb
1
17
14
12
12
5
11
2
N
3
N
4
6
9
N
N
13
N
15 ± 3 N·m
11 ± 2 ft-lb
15 ± 3 N·m
11 ± 2 ft-lb
N
8
10
12 ± 2 N·m
102 ± 22 in-lb
18
4
N
REMOVAL STEPS
1.
STEERING SHAFT PAD
<<A>>
2.
STEERING COLUMN ASSEMBLY
AND STEERING GEAR
CONNECTION
<<B>>
3.
SELF LOCKING NUTS
(CONNECTION FOR TIE ROD
END)
<<B>>
4.
SELF LOCKING NUTS
(CONNECTION FOR LOWER
ARM BALL JOINT)
5.
LOWER ARM ASSEMBLY
6.
STABILIZER LINK CONNECTION
7.
RETURN TUBE CONNECTION
8.
O-RING
9.
PRESSURE HOSE CONNECTION
10. O-RING
11. PRESSURE HOSE CLAMP
12. SELF LOCKING NUTS
>>D<<
13. SELF LOCKING NUTS
REMOVAL STEPS (Continued)
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-15
Required Special Tool:
• MB991897: Ball Joint Remover
REMOVAL SERVICE POINTS
.
<<A>> STEERING COLUMN ASSEMBLY AND
STEERING GEAR DISCONNECTION
Pinch the steering column shaft clip with pliers, and pull up the
shaft in the direction shown to disengage the steering column
assembly.
14. FRONT AXLE CROSSMEMBER
STAY
15. ENGINE REAR ROLL STOPPER
BRACKET, POWER STEERING
GEAR AND LINKAGE,
STABILIZER BAR AND FRONT
AXLE NO.1 CROSSMEMBER
ASSEMBLY
>>B<<
16. ENGINE REAR ROLL STOPPER
BRACKET
>>B<<
17. POWER STEERING GEAR
BRACKET
18. STEERING GEAR AND LINKAGE
PROTECTOR
19. POWER STEERING GEAR AND
LINKAGE
>>A<<
20. STABILIZER BAR
21. FRONT AXLE NO.1
CROSSMEMBER
REMOVAL STEPS (Continued)
AC306565 AB
CLIP
STEERING
COLUMN
SHAFT
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-16
NOTE: If the steering column shaft is removed accidentally,
remove the steering column assembly and be sure to insert the
steering column shaft into the steering column as shown in the
figure.
.
<<B>> SELF LOCKING NUTS (CONNECTION FOR
TIE ROD END AND LOWER ARM BALL JOINT)
REMOVAL
CAUTION
• Do not remove the nut from ball joint. Loosen it and use
special tool MB991897 to avoid possible damage to ball
joint threads.
• Hang special tool MB991897 with a cord to prevent it
from falling.
1. Replace the self locking nut for lower arm ball joint with a
regular nut, because the original one is a little bit large to
install special tool MB991897. Install special tool MB991897
as shown in the figure.
2. Turn the bolt and knob as necessary to make the jaws of
special tool parallel, tighten the bolt by hand and confirm
that the jaws are still parallel.
NOTE: When adjusting the jaws in parallel, make sure the
knob is in the position shown in the figure.
3. Tighten the bolt with a wrench to disconnect the lower arm
ball joint, tie rod end and remove the self locking nut.
.
AC306564 AB
X
X
Y
Y
X
X
Y
Y
YOKE Y
VIEW A
7.6˚ ± 3˚
YOKE X
A
AC208247AC
CORD
BOLT
MB991897
NUT
BALL JOINT
AC106821
KNOB
PARALLEL
BOLT
CORRECT
WRONG
AC
CROSSMEMBER
TSB Revision
POWER PLANT MOUNT
32-17
<<C>> FRONT AXLE CROSSMEMBER STOPPER
REMOVAL
The crossmember mounting bolts need not be unscrewed
when the front axle crossmember stopper is replaced. How-
ever, the bolts may become loosened when the front axle
crossmember stopper is removed. Retighten the bolts to 180
±
20 N
⋅m (133 ± 15 ft-lb).
.
<<D>> FRONT AXLE CROSSMEMBER STAY
REMOVAL
The crossmember mounting bolts need not be unscrewed
when the front axle crossmember stay is replaced. However,
the bolts may become loosened when the front axle crossmem-
ber stay is removed. Retighten the bolts to 180
± 20 N⋅m (133 ±
15 ft-lb).
.
<<E>> ENGINE REAR ROLL STOPPER BRACKET,
POWER STEERING GEAR AND LINKAGE,
STABILIZER BAR AND FRONT AXLE NO.1
CROSSMEMBER ASSEMBLY REMOVAL
Support the front axle number 1 crossmember with a transmis-
sion jack, and then remove the crossmember mounting nuts
and bolts.
AC307551AB
FRONT AXLE
CROSSMEMBER
STOPPER
CROSSMEMBER
MOUNTING BOLT
AC306568 AB
FRONT AXLE
CROSSMEMBER
STAY
CROSSMEMBER
MOUNTING BOLT
AC206593
AC306696
TRANSMISSION
JACK
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст