Mitsubishi Galant 9G. Manual — part 145
HEADLINING
TSB Revision
INTERIOR
52A-18
HEADLINING
REMOVAL AND INSTALLATION
M1521001400360
WARNING
When removing and installing the front passenger seat, be sure to carry out accuracy check
occupant classification sensor after the seat has been installed in the vehicle. (Refer to
GROUP 52B, On-Vehicle Service
Pre-removal and Post-installation Operation
• Front Seat Assembly (Refer to
• Removal and Installation of Rear Seat Cushion Assembly
and Rear Seatback Assembly (Refer to
• Removal and Installation of Front Pillar Trim, Center Pillar
Trim Upper and Rear Pillar Trim (Refer to
AC307811
NOTE
: CLIP POSITION
SECTION A – A
11
1
2
3
2
1
12
4
13
6
15
16
14
7
10
10
3
CLIP
AB
5
11
A
A
8
9
REMOVAL STEPS
1.
SUN VISOR
2.
SUN VISOR HOLDER
3.
OVERHEAD CONSOLE
ASSEMBLY
4.
DOME LIGHT ASSEMBLY (REFER
TO GROUP 54A, DOME LIGHT
5.
ASSIST GRIP PLUG
6.
ROOF INSIDE ASSIST GRIP
<VEHICLES WITH ROOF INSIDE
ASSIST GRIP>
7.
SUNROOF OPENING TRIM
<VEHICLES WITH SUNROOF>
8.
ROOF HARNESS CLAMP
•
INSTRUMENT PANEL SIDE
COVER (REFER TO
9.
ROOF HARNESS CONNECTOR
REMOVAL STEPS (Continued)
INSIDE REAR VIEW MIRROR
TSB Revision
INTERIOR
52A-19
REMOVAL SERVICE POINT
.
<<A>> HEADLINING ASSEMBLY REMOVAL
Remove the front passenger's door check (body side mounting
bolt), open the front passenger's door and remove the headlin-
ing assembly. (Refer to GROUP 42, Door Assembly
INSIDE REAR VIEW MIRROR
M1521002600248
REMOVAL SERVICE POINT
.
INSIDE REAR VIEW MIRROR REMOVAL
Insert a narrow flat-tip screwdriver into the slit in the inside rear
view mirror bracket, keep the spring pushed in and remove the
inside rear view mirror in the direction of the arrow in the illus-
tration.
NOTE: While the spring is pushed in, the connection between
the spring and the pawl of the button is released.
•
FLOOR CONSOLE ASSEMBLY
(REFER TO
.)
•
PARKING BRAKE LEVER
ASSEMBLY MOUNTING BOLT
(REFER TO GROUP 36, PARKING
BRAKE LEVER
<<A>>
10. HEADLINING ASSEMBLY
11. OVERHEAD CONSOLE BRACKET
12. FRONT HEADLINING PAD
13. CENTER HEADLINING PAD
14. REAR HEADLINING PAD
15. ROOF INSIDE ASSIST GRIP
BRACKET <VEHICLES WITH
ROOF INSIDE ASSIST GRIP>
16. ASSIST GRIP BRACKET
REMOVAL STEPS (Continued)
AC307195 AB
FRONT PASSENGER'S
DOOR CHECK
AC000333 AB
BUTTON
BRACKET
SPRING
SLIT
FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-20
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATION
M1522001300560
WARNING
•
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions
and Air Bag Module and Clock Spring
•
When removing and installing the front passenger seat, be sure to carry out accuracy
check occupant classification sensor after the seat has been installed in the vehicle.
(Refer to GROUP 52B, On-Vehicle Service
CAUTION
Do not impact the seat. If the impact (falling etc.) is applied on the seat with occupant classification
sensor, the occupant classification sensor transmitting error may be occurred.)
Post-installation Operation
Adjustment Procedures of Special Function (refer to GROUP
52B, On-Vehicle Service
.)
FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR
52A-21
AC307257
7
6
5
3
8
10
2
8
44 ± 10 N·m
33 ± 7 ft-lb
30 ± 5 N·m
22 ± 4 ft-lb
8
3
4
7
8
44 ± 10 N·m
33 ± 7 ft-lb
2
10
30 ± 5 N·m
22 ± 4 ft-lb
AB
1
5
4
9
1.
HEATED SEAT SWITCH
<VEHICLES WITH HEATED
SEAT>
2.
HEADREST
FRONT SEAT ASSEMBLY
REMOVAL STEPS
3.
SEAT BELT SWITCH
CONNECTOR
4.
SEAT SLIDE SENSOR (DRIVER’S
SIDE), OCCUPANT
CLASSIFICATION SENSOR
(PASSENGER’S SIDE)
5.
HEATED SEAT CONNECTOR
<VEHICLES WITH HEATED
SEAT>
6.
POWER SEAT CONNECTOR
<VEHICLES WITH POWER SEAT>
7.
SIDE-AIR BAG MODULE
CONNECTOR <VEHICLES WITH
SIDE-AIR BAG>
8.
FRONT SEAT REAR ANCHOR
COVER
9.
OUTER SEAT BELT
(PASSENGER’S SIDE)
>>A<<
10. FRONT SEAT ASSEMBLY
FRONT SEAT ASSEMBLY
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст