Mitsubishi Galant 9G. Manual — part 841
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-806
Check Conditions
• Engine coolant temperature is higher than 20°C
(68
°F).
• Vehicle speed is higher than 50 km/h (31 mph).
Judgment Criteria
• The ON/OFF frequency of a power steering pres-
sure switch is 10 Hz or more for 20 seconds.
.
OBD-II DRIVE CYCLE PATTERN
None.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Power steering pressure switch failed.
• Incorrect power steering fluid level.
• Incorrect oil pump pressure.
• Harness damage in power steering pressure
switch circuit, or connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, check data list item 27:
Power Steering Pressure Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
27, Power Steering Pressure Switch.
• If the steering wheel is not turned while idling, "OFF" will
be displayed.
• If the steering wheel is turned while idling, "ON" will be
displayed.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
STEP 2. Check the power steering fluid level.
Refer to GROUP 37, On-Vehicle Service
− Fluid Level Check
Q: Are there any abnormalities?
YES : Repair it. Then go to Step 7.
NO : Go to Step 3.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-807
STEP 3. Check the power steering pressure switch.
Refer to GROUP 37, On-Vehicle Service
− Power Steering
Pressure Switch Check
.
Q: Are there any abnormalities?
YES : Replace the power steering pressure switch. Then go
to Step 7.
NO : Go to Step 4.
STEP 4. Check the oil pump pressure.
Refer to GROUP 37, On-Vehicle Service
− Oil Pump Pressure
Q: Are there any abnormalities?
YES : Repair it. Then go to Step 7.
NO : Go to Step 5.
STEP 5. Check harness connector B-31 at the power
steering pressure switch and harness connector B-21 at
PCM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 7.
AK303881
1
AB
CONNECTOR: B-31
B-31 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-808
STEP 6. Check for harness damage between power
steering pressure switch connector B-31 (terminal No. 1)
and PCM connector B-21 (terminal No. 78).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 7.
NO : Repair it. Then go to Step 7.
AK303881
1
AB
CONNECTOR: B-31
B-31 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-809
STEP 7. Using scan tool MB991958, check data list item 27:
Power Steering Pressure Switch.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
27, Power Steering Pressure Switch.
• If the steering wheel is not turned while idling, "OFF" will
be displayed.
• If the steering wheel is turned while idling, "ON" will be
displayed.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : The inspection is complete.
NO : Retry the troubleshooting.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
NEXT>>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст