Mitsubishi Galant 9G. Manual — part 1163
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-952
STEP 4. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 8.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-953
STEP 5. Check for open circuit and harness damage
between accelerator pedal position sensor connector C-24
(terminal No. 2) and PCM connector B-20 (terminal No. 31).
Q: Is the harness wire in good condition?
YES : Go to Step 7.
NO : Repair it. Then go to Step 8.
STEP 6. Replace the accelerator pedal position sensor.
(1) Replace the accelerator pedal position sensor.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P2123 set?
YES : Replace the PCM. Then go to Step 8.
NO : The inspection is complete.
AK303202
1
6 5 4 3 2
ACCELERATOR
PERAL
AB
CONNECTOR: C-24
C-24 (B)
ACCELERATOR
PEDAL POSITION
SENSOR
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303202
1
6 5 4 3 2
ACCELERATOR
PERAL
AB
CONNECTOR: C-24
C-24 (B)
ACCELERATOR
PEDAL POSITION
SENSOR
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-954
STEP 7. Using scan tool MB991958, check data list item 78:
Accelerator Pedal Position Sensor (main).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
78, Accelerator Pedal Position Sensor (main).
• Output voltage is between 0.7 and 1.3 volts when foot is
released from accelerator pedal.
• Output voltage is 4.0 volts or higher when accelerator
pedal is fully depressed.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Replace the PCM. Then go to Step 8.
STEP 8. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2123 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-955
DTC P2127: Accelerator Pedal Position Sensor (sub) Circuit Low Input
CAUTION
If DTC P2127 has been set, TCL related DTC
U1120 is also set. After P2127 has been diag-
nosed, don't forget to erase DTC U1120.
.
AK302873
YELLO
W
-RED
PINK-GREEN
BR
O
W
N
5 V
21
4
ACCELERATOR PEDAL
POSITION SENSOR (SUB)
HALL IC
POWERTRAIN CONTROL
MODULE (PCM)
27
22
6
5
Accelerator Pedal Position Sensor (sub) Circuit
B-20
C-24
6
1 2 3 4 5
22
21
23 24 25
26 27 28 29
30 31 32 33 34
35 36 37 38
39 40 41 42 43
AK303201
ACCELERATOR
PERAL
AB
CONNECTOR: C-24
C-24 (B)
ACCELERATOR
PEDAL POSITION
SENSOR
AK303085
CONNECTOR: B-20
PCM
AB
AIR CLEANER
B-20
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст