Mitsubishi Galant 9G. Manual — part 1246
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-88
(3) Measure the voltage between joint connector (3) terminal
17 and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between joint connector (3) and the
A/C-ECU connector.
STEP 15. Check the CAN_H line (communication line
including the SRS-ECU) between joint connector (3) and
the SRS-ECU connector for short to the power supply.
Measure the voltage at joint connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect joint connector (3) C-02, and measure the
voltage at the wiring harness side of joint connector (3)
C-02.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between joint connector (3) terminal 3
and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 21.
NO : If the voltage measures more than 4.0 V, go to Step
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365
AC209365GD
HARNESS SIDE: C-02
TEST
HARNESS
AC305231AP
CONNECTOR: C-02
AC209365
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
AC209365FU
HARNESS SIDE: C-02
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-89
STEP 16. Check intermediate connector C-22 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is intermediate connector C-22 in good condition?
YES : Go to Step 17.
NO : Repair the damaged parts.
STEP 17. Check the CAN_H-side bus line (communication
line including ECUs) of the floor wiring harness for short
to the power supply. Measure the voltage at intermediate
connector C-22.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect intermediate connector C-22, and measure the
voltage at the male side (at floor wiring harness side).
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between intermediate connector
terminal 22 and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 20 .
NO : If the voltage measures more than 4.0 V, go to Step
AC305233 AI
CONNECTOR: C-22
C-22 (Y)
AC305233 AI
CONNECTOR: C-22
C-22 (Y)
AC209365
AC209365FT
MAIL SIDE: C-22
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-90
STEP 18. Check SRS-ECU connector C-121 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is SRS-ECU connector C-121 in good condition?
YES : Go to Step 19.
NO : Repair the damaged parts.
STEP 19. Check the CAN_ H line (communication line only)
between the SRS-ECU connector and the intermediate
connector for a short circuit. Measure the voltage at
intermediate connector C-22.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect intermediate connector C-22 and SRS-ECU
connector C-121, and measure the voltage at the male side
of intermediate connector C-22 (at floor wiring harness
side).
(2) Turn the ignition switch to the "ON" position.
AC305233 AJ
CONNECTOR: C-121
HARNESS SIDE
C-121 (Y)
48
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
AC305234AC
CONNECTORS: C-22, C-121
C-121 HARNESS SIDE
C-121 (Y)
C-22 (Y)
C-22
48
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-91
(3) Measure the voltage between intermediate connector
terminal 22 and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between intermediate connector C-22
and SRS-ECU connector.
STEP 20. Check the CAN_H line (communication line only)
between joint connector (3) and the intermediate
connector for a short circuit. Measure the voltage at joint
connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect intermediate connector C-22 and joint
connector (3) C-02, and measure the voltage at the wiring
harness side of joint connector (3) C-02.
(2) Turn the ignition switch to the "ON" position.
AC209365
AC209365FT
MAIL SIDE: C-22
TEST
HARNESS
AC305231AP
CONNECTOR: C-02
AC305233 AI
CONNECTOR: C-22
C-22 (Y)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст