Mitsubishi Galant 9G. Manual — part 1378
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-6
MD998718
Crankshaft rear oil seal
installer
MD998718-01
Press-fitting the crankshaft rear oil
seal
MD998767
Tension pulley socket
wrench
MD998752-01
Timing belt tension adjustment
MD998769
Crankshaft pulley spacer
General service
tool
Rotating the crankshaft when
installing the timing belt
MD998772
Valve spring compressor
General service
tool
Compressing valve spring
MD998774
Valve stem seal installer
MD998774-01
Valve stem seal installer
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
D998767
AC204024
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-7
MB991454
Engine hanger balancer
MZ203827-01
When the engine hanger is used:
Supporting the engine assembly
during removal and installation of
the transaxle assembly
NOTE: Special tool MB991454 is a
part of engine hanger attachment
set MB991453.
MB991895
Engine hanger
Tool not available
MB991928
Engine hanger
A: MB991929
Joint (50)
×2
B: MB991930
Joint (90)
×2
C: MB991931
Joint (140)
×2
D: MB991932
Foot (standard)
×4
E: MB991933
Foot (short)
×2
F: MB991934
Chain and hook
assembly
Tool not available
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
B991454
MB991895
B991928
A
B
C
D
E
F
SLIDE BRACKET (HI)
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-8
ON-VEHICLE SERVICE
DRIVE BELT TENSION CHECK AND
ADJUSTMENT
M1111003100496
Refer to GROUP 00, Maintenance Service
− Drive Belts
(Check Condition)
IGNITION TIMING CHECK
M1111001701075
Required Special Tool:
MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
1. Before inspection, set the vehicle in the following condition:
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights and all accessories: OFF
• Transaxle: P range
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Set the timing light to the power supply line (terminal No. 1)
of the ignition coil No. 1.
NOTE: The power supply line is looped and also longer than
the other ones.
4. Start the engine and run it at idle.
5. Check that the idle speed is approximately 680 r/min.
6. Select scan tool MB991958 actuator test "item number 17".
7. Check that basic ignition timing is within the standard value.
Standard value: 5
° BTDC ± 3°
8. If the basic ignition timing is not within the standard value,
check the following items:
• Diagnostic output
• Timing belt cover and crankshaft position sensor installation
conditions
• Crankshaft sensing blade condition
CAUTION
If the actuator test is not canceled, the forced drive will
continue for 27 minutes. Driving in this state could lead to
engine failure.
9. Press the clear key on scan tool MB991958 (select forced
drive stop mode), and cancel the actuator test.
10.Check that the actual ignition timing is at the standard value.
Standard value: Approximately 10
° BTDC
AC302077
AC305412
AC306958AB
MB991824
MB991910
MB991668
DATA LINK
CONNECTOR
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <3.8L ENGINE>
11C-9
NOTE: Ignition timing fluctuates about
±
7
°
Before Top Dead
Center, even under normal operating condition.
NOTE: It is automatically further advanced by about 5
°
to
10
°
Before Top Dead Center at higher altitudes.
CURB IDLE SPEED CHECK
M1111003501044
Required Special Tool:
MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
1. Before inspection, set the vehicle in the following condition:
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights and all accessories: OFF
• Transmission: P range
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Check the basic ignition timing.
Standard value: 5
° BTDC ± 3°
4. Start the engine.
5. Run the engine at idle for 2 minutes.
6. Check the idle speed. Select item number 22 and take a
reading of the idle speed.
Curb idle speed: 680
± 100 r/min
NOTE: The idle speed is controlled automatically by the idle
air control system.
7. If the idle speed is outside the standard value, refer to
GROUP 13B, Multiport Fuel Injection (MFI) <3.8L Engine>
−
Multiport Fuel Injection (MFI) Diagnosis
− Symptom Chart
.
AC302077
AC305412
AC306958AB
MB991824
MB991910
MB991668
DATA LINK
CONNECTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст