Mitsubishi Galant 9G. Manual — part 324
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-12
7. While shutting up the oil passage hole at the depth of the
engine oil control valve's installation hole by finger not to
leak air, blow compression air into the engine oil pressure
switch's installation hole by air blowgun. At this time, confirm
that the rocker arm piston can operate.
NOTE: To fully confirm the check, prevent the compression air
from leaking as much as possible by installing the O-ring to the
end of air blowgun.
8. Turn the crankshaft clockwise until the notch on the
crankshaft pulley is lined up with "T" mark on the lower cover
of timing belt.
9. Confirm the rest of the rocker arm pistons under the
procedure 7.
10.When the rocker arm piston does not operate, replace the
rocker arm assy.
11.Install the engine oil pressure switch and the engine oil
control valve. (Refer to Camshaft and Valve Stem Seal
−
Removal and Installation
12.Install the rocker cover.
13.Install all of the ignition coils.
IGNITION TIMING CHECK
M1111001701064
Required Special Tool:
MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
1. Before inspection, set the vehicle in the following condition:
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights and all accessories: OFF
• Transaxle: P range
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
AK302684AB
ROCKER ARM
PISTON
BLOW
COMPRESSION
AIR
OIL PASSAGE
ROCKER
ARM
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-13
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Set the timing light to the power supply line (terminal No. 1)
of the ignition coil No. 1.
NOTE: The power supply line is looped and also longer than
the other ones.
4. Start the engine and run it at idle.
5. Check that the idle speed is approximately 700 r/min.
6. Select scan tool MB991958 actuator test "item number 17".
7. Check that basic ignition timing is within the standard value.
Standard value: 5
° BTDC ± 3°
8. If the basic ignition timing is not within the standard value,
check the following items:
• Diagnostic output
• Timing belt cover and crankshaft position sensor installation
conditions
• Crankshaft sensing blade condition
CAUTION
If the actuator test is not canceled, the forced drive will
continue for 27 minutes. Driving in this state could lead to
engine failure.
9. Press the clear key on scan tool MB991958 (select forced
drive stop mode), and cancel the actuator test.
10.Check that the actual ignition timing is at the standard value.
Standard value: Approximately 10
° BTDC
NOTE: Ignition timing fluctuates about
±
7
°
Before Top Dead
Center, even under normal operating condition.
NOTE: It is automatically further advanced by about 5
°
to
10
°
Before Top Dead Center at higher altitudes.
AC302077
AC305412
AC306958AB
MB991824
MB991910
MB991668
DATA LINK
CONNECTOR
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-14
CURB IDLE SPEED CHECK
M1111003500999
Required Special Tool:
MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
1. Before inspection, set the vehicle in the following condition.
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights and all accessories: OFF
• Transaxle: P range
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Check the basic ignition timing.
Standard value: 5
° BTDC ± 3°
4. Start the engine.
5. Run the engine at idle for 2 minutes.
6. Check the idle speed. Select item number 22 and take a
reading of the idle speed.
Curb idle speed: 700
± 100 r/min
NOTE: The idle speed is controlled automatically by the idle
air control system.
7. If the idle speed is outside the standard value, refer to
GROUP 13A, Multiport Fuel Injection (MFI) <2.4L Engine>
−
Multiport Fuel Injection (MFI) Diagnosis
− Symptom Chart
.
AC302077
AC305412
AC306958AB
MB991824
MB991910
MB991668
DATA LINK
CONNECTOR
ON-VEHICLE SERVICE
TSB Revision
ENGINE MECHANICAL <2.4L ENGINE>
11A-15
IDLE MIXTURE CHECK
M1111002100749
Required Special Tool:
MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
1. Before inspection, set the vehicle in the following condition:
• Engine coolant temperature: 80 − 95°C (176 − 203°F)
• Lights and all accessories: OFF
• Transaxle: P range
NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Check that the basic ignition timing is within the standard
value.
Standard value: 5
° BTDC ± 3°
4. Start the engine and increase the engine speed to 2,500
r/min for 2 minutes.
5. Set the CO, HC tester.
6. Check the CO contents and the HC contents at idle.
Standard value:
CO contents: 0.5 % or less
HC contents: 100 ppm or less
7. If the CO and HC contents do not remain inside the standard
value, check the following items:
NOTE: Replace the catalytic converter when the CO and HC
contents do not remain inside the standard value, even
though the result of the inspection is normal for all items.
• Diagnostic output
• Closed-loop control (When the closed-loop control is carried
out normally, the output signal of the heated oxygen sensor
changes between 0
− 400 mV and 600 − 1,000 mV at idle.)
• Fuel pressures
• Injector
• Ignition coil, spark plug
• EGR system
• Evaporative emission system
• Compression pressure
AC302077
AC305412
AC306958AB
MB991824
MB991910
MB991668
DATA LINK
CONNECTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст