Mitsubishi Galant 9G. Manual — part 259
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-112
INSPECTION PROCEDURE 3: Outside/Inside Air Changeover is not possible.
A/C-ECU
OUTSIDE/INSIDE
AIR SELECTION
DAMPER CONTROL
MOTOR
IGNITION
SWITCH (IG2)
JUNCTION
BLOCK
JOINT
CONNECTOR (2)
MOTOR DRIVE
CIRCUIT
Outside/Inside Air Selection Motor Circuit
AC305231AZ
CONNECTOR: C-03
AC305233BK
CONNECTORS: C-09, C-106
C-09 (B)
C-106
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-113
.
CIRCUIT OPERATION
If the outside/inside air selection damper control
motor does not operate normally, the outside/inside
air selection damper control motor system may be
defective.
.
TROUBLESHOOTING HINTS
• Malfunction of the outside/inside air selection
damper control motor
• Malfunction of the A/C-ECU
• Damaged harness wires or connectors
DIAGNOSIS
Required Special Tool:
• MB991223: Test Harness Set
STEP 1. Check the defogger and A/C operations.
Q: Do the defogger and A/C work normally?
YES : Go to Step 2.
NO : Refer to Inspection procedure 10 "Malfunction of the
A/C-ECU power supply system
STEP 2. Check outside/inside air selection damper control
motor connector C-106 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is outside/inside air selection damper control motor
connector C-106 in good condition?
YES : Go to Step 3.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
. Check
that the outside/inside air selection damper control
motor works normally.
AC305415
CONNECTORS: C-211, C-215
JUNCTION BLOCK
(FRONT VIEW)
C-215
C-211
BA
AC305233
HARNESS SIDE
BJ
CONNECTOR: C-106
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-114
STEP 3. Measure the voltage at outside/inside air selection
damper control motor connector C-106.
(1) Disconnect outside/inside air selection damper control
motor connector C-106, and measure the voltage at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Does the measured voltage correspond with this range?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check the wiring harness between outside/inside
air selection damper control motor connector C-106
(terminal 1) and the ignition switch (IG2).
AC305233
HARNESS SIDE
BJ
CONNECTOR: C-106
AC209365
CONNECTOR C-106
(HARNESS SIDE)
GR
AC305233
HARNESS SIDE
BJ
CONNECTOR: C-106
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-115
NOTE: Also check joint connector C-03, junction block connec-
tors C-211 and C-215 for loose, corroded, or damaged termi-
nals, or terminals pushed back in the connector. If intermediate
connector C-03, junction block connector C-211 or C-215 is
damaged, repair or replace the connector as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between outside/inside air
selection damper control motor connector C-106
(terminal 1) and the ignition switch (IG2) in good
condition?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Repair the wiring harness. Check that the
outside/inside air selection damper control motor
works normally.
AC305231BP
CONNECTOR: C-03
AC305416
CONNECTORS: C-211, C-215
JUNCTION BLOCK
(FRONT VIEW)
C-215
C-211
HARNESS SIDE
C-211
HARNESS SIDE
C-215
AK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст