Mitsubishi Galant 9G. Manual — part 979
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-216
• At least 20 seconds have passed since fuel shut
off control was canceled.
• Monitoring time: 8 seconds.
Judgement Criteria
• Making the air/fuel ratio 15 percent richer for 8
seconds does not result in raising the heated oxy-
gen sensor (front) output voltage beyond 0.2 volt.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
− Other Monitor
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Right bank heated oxygen sensor (front) failed.
• Short circuit in right bank heated oxygen sensor
(front) output line.
• Connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
• MD998464: Test Harness
STEP 1. Using scan tool MB991958, check data list item 39:
Heated Oxygen Sensor Bank 1, Sensor 1 (right front).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
39, Heated Oxygen Sensor Bank 1, Sensor 1 (right front).
• Warm up the engine. When the engine is revved, the
output voltage should measure 0.6 to 1.0 volt.
• Warm up the engine. When the engine is idling, the out-
put voltage should repeat 0.4 volt and 0.6 to 1.0 volt
alternately.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-217
STEP 2. Check the right bank heated oxygen sensor
(front).
(1) Disconnect the right bank heated oxygen sensor (front)
connector B-09 and connect test harness special tool,
MD998464, to the connector on the right bank heated
oxygen sensor (front) side.
(2) Warm up the engine until engine coolant temperature
reaches 80
°C (176°F) or higher.
(3) Perform a racing for 5 minutes or more with the engine
speed of 4,500 r/min.
(4) Connect a digital voltage meter between terminal No. 2
(black clip) and terminal No. 4 (white clip).
(5) While repeatedly revving the engine, measure the right
bank heated oxygen sensor (front) output voltage.
Standard value: 0.6
− 1.0 volt
CAUTION
• Be very careful when connecting the jumper wires;
incorrect connection can damage the heated oxygen
sensor.
• Be careful the heater is broken when voltage of beyond
8 volts is applied to the heated oxygen sensor heater.
NOTE: If the sufficiently high temperature [of approximate
400
°
C (752
°
F) or more] is not reached although the heated
oxygen sensor is normal, the output voltage would be possi-
bly low although the rich air/fuel ratio. Therefore, if the out-
put voltage is low, use a jumper wire to connect the terminal
No.1 (red clip) and the terminal No. 3 (blue clip) of the
heated oxygen sensor with the positive terminal and the
negative terminal of 8 volts power supply respectively, then
check again.
Q: Is the voltage between 0.6 and 1.0 volt?
YES : Go to Step 3.
NO : Replace the right bank heated oxygen sensor (front).
Then go to Step 5.
1
2
3
4
AK303048
B-09 (B)
CONNECTOR: B-09
THROTTLE BODY
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01624
HEATED
OXYGEN
SENSOR
COMPONENT
SIDE
CONNECTOR
MD998464
WHITE
BLACK
AQ
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-218
STEP 3. Check harness connector B-09 at right bank
heated oxygen sensor (front) and connector B-22 at PCM
for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 5.
1
2
3
4
AK303048
B-09 (B)
CONNECTOR: B-09
THROTTLE BODY
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-219
STEP 4. Check for short circuit to ground between right
bank heated oxygen sensor (front) connector B-09
(terminal No. 4) and PCM connector B-22 (terminal No. 92).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 5.
NO : Repair it. Then go to Step 5.
1
2
3
4
AK303048
B-09 (B)
CONNECTOR: B-09
THROTTLE BODY
RIGHT BANK
HEATED OXYGEN
SENSOR (FRONT)
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст