Mitsubishi Galant 9G. Manual — part 964
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-156
STEP 4. Measure the sensor supply voltage at PCM
connector B-22 by using power plant ECU check harness
special tool MB991923.
(1) Do not disconnect the all PCM connectors and connect
power plant ECU check harness special tool MB991923
between the separated connectors.
(2) Disconnect the engine coolant temperature sensor
connector B-104.
(3) Turn the ignition switch to the "ON" position.
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-157
(4) Measure the voltage between terminal No. 93 and ground.
• Voltage should be between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 5.
NO : Go to Step 6.
AK202956
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
AK203047AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-158
STEP 5. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between engine coolant
temperature sensor connector B-104 (termial No. 1)
and PCM connector B-22 (termial No. 93) because of
open circuit. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
STEP 6. Check harness connector B-22 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-159
STEP 7. Check the continuity at engine coolant
temperature sensor harness side connector B-104.
(1) Disconnect the connector B-104 and measure at the
harness side.
(2) Check for the continuity between terminal No. 2 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 10.
NO : Go to Step 8.
STEP 8. Check harness connector B-21 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
1
2
AK303037
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-104
AB
B-104 (B)
THROTTLE
BODY
AK303040
B-104 HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
AB
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст