Mitsubishi Galant 9G. Manual — part 1328
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-416
STEP 7. Check the CAN bus lines (communication line
only) between intermediate connector C-29 and joint
connector (3). Measure the resistance at intermediate
connector C-29 and joint connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect joint connector (3) C-02 and intermediate
connector C-29, and measure the resistance between the
wiring harness side connector of joint connector (3) C-02
and the female side connector of intermediate connector
C-29 (instrument panel wiring harness side).
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
(3) Disconnect the negative battery terminal.
AC305232
CONNECTORS: C-02, C-29
AG
C-02
C-02
C-29
C-29
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-417
(4) Measure the resistance between intermediate connector
terminal 12 and joint connector (3) terminal 20.
OK: 2 ohms or less
(5) Measure the resistance between intermediate connector
terminal 11 and joint connector (3) terminal 9.
OK: 2 ohms or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Do all the resistances measure 2 ohms or less?
YES : If all the resistances measure 2 ohms or less, go to
Step 2.
NO : If either of the resistances measures more than 2
ohms or all the resistances measure more than 2
ohms, repair the wiring harness between joint
connector (3) and the intermediate connector, and
then go to Step 2.
AC204582
35
34
36
30
38
29
17
13 12 11
37
31
33 32
26
27
28
16
14
15
3 2
4
18
6
7
21 20
5
19
9
10
24 23
25
8
22
1
TEST
HARNESS
FEMALE SIDE: C-29
HARNESS SIDE: C-02
TEST
HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
DF
AC204582
35
34
36
30
38
29
17
13 12 11
37
31
33 32
26
27
28
16
14
15
3 2
4
18
6
7
21 20
5
19
9
10
24 23
25
8
22
1
TEST
HARNESS
FEMALE SIDE: C-29
HARNESS SIDE: C-02
TEST HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
DE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-418
STEP 8. Check the front wiring harness side CAN bus lines
(communication line including the powertrain control
module and the ABS-ECU). Measure the resistance at
intermediate connector C-29.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect intermediate connector C-29, and measure the
resistance at the male side (at front wiring harness side).
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
(3) Disconnect the negative battery terminal.
(4) Measure the resistance between intermediate connector
terminals 11 and 12.
OK: 120
± 20 Ω
Q: Does the resistance measure 120
± 20 Ω?
YES : If the resistance measures 120
± 20 Ω, go to Step 15.
NO : If the resistance does not measure 120
± 20 Ω, go to
Step 9 .
AC305231AI
CONNECTOR: C-29
AC204582
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
BX
TEST
HARNESS
TEST
HARNESS
MALE SIDE: C-29
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-419
STEP 9. Check ABS-ECU connector A-02 and powertrain
control module connector B-19 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Are ABS-ECU connector A-02 and powertrain control
module connector B-19 in good condition?
YES : Go to Step 10.
NO : Repair the damaged parts. Then go to Step 8.
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
AC306248AD
B-19 (B)
CONNECTOR: B-19
PCM
AIR
CLEANER
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст