Mitsubishi Galant 9G. Manual — part 1332
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-432
STEP 3. Check joint connector (3) C-02 and combination
meter connector C-101 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Check the joint connector at the wiring harness side for loose,
corroded or damaged terminals, or terminals pushed back in
the connector, and also check the short pin behind the connec-
tor for corrosion, deformation and delamination.
Q: Are joint connector (3) C-02 and combination meter
connector C-101 in good condition?
YES : Go to Step 4.
NO : Repair the damaged parts. Replace the joint
connector as necessary.
AC305232
HARNESS SIDE
C-101
CONNECTORS: C-02, C-101
AE
C-02
C-02
C-101
AC209350
1
12
2
13
3
14
4
15
5
16
6
17
7
18
8
19
9
20
10
21
11
22
AB
SHORT PIN
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-433
STEP 4. Check the CAN bus lines (communication line
including the combination meter) between joint connector
(3) and the combination meter. Measure the resistance at
joint connector (3) C-02.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect joint connector (3) C-02, and measure the
resistance at the wiring harness side of joint connector (3)
C-02.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
(3) Disconnect the negative battery terminal.
(4) Measure the resistance between joint connector (3)
terminals 4 and 15.
OK: 120
± 20 Ω
Q: Does the resistance measure 120
± 20 Ω?
YES : If the resistance measures 120
± 20 Ω, diagnose CAN
bus lines thoroughly by referring to
NO : If the resistance does not measure 120
± 20 Ω, go to
Step 5 .
AC305231AP
CONNECTOR: C-02
AC209438
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
TEST
HARNESS
AQ
TEST
HARNESS
HARNESS SIDE: C-02
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-434
STEP 5. Check the CAN bus lines (communication line
only) between joint connector (3) and the combination
meter. Measure the resistance at joint connector (3) C-02
and combination meter connector C-101.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect joint connector (3) C-02 and combination meter
connector C-101, and measure the resistance between
each wiring harness side connector.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
(3) Disconnect the negative battery terminal.
AC305232
HARNESS SIDE
C-101
CONNECTORS: C-02, C-101
AE
C-02
C-02
C-101
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-435
(4) Measure the resistance between joint connector (3)
terminal 15 and combination meter connector terminal 15.
OK: 2 ohms or less
(5) Measure the resistance between joint connector (3)
terminal 4 and combination meter connector terminal 14.
OK: 2 ohms or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Do all the resistances measure 2 ohms or less?
YES : If the resistance measures 2 ohms or less, go to Step
NO : If either of the resistances measures more than 2
ohms or all the resistances measure more than 2
ohms, repair the wiring harness between joint
connector (3) and the combination meter connector.
AC204582
HARNESS SIDE: C-02
BZ
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
G
G
22
11
5
16
19
20
21
17
18
8
10 9
7 6
13
1514
12
2
4 3
1
TEST
HARNESS
HARNESS SIDE: C-101
TEST
HARNESS
AC204582
HARNESS SIDE: C-02
TEST
HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
G
G
22
11
5
16
19
20
21
17
18
8
10 9
7 6
13
1514
12
2
4 3
1
TEST
HARNESS
HARNESS SIDE: C-101
CA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст