Mitsubishi Galant 9G. Manual — part 1539
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-28
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
STEP 1. Check the battery voltage.
Measure the battery voltage during cranking.
Q: Is the voltage 8 volts or more?
YES : Go to Step 2.
NO : Check the condition of the battery. Refer to
.
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch "ON" position.
(3) Read the diagnosis code.
Q: Have any DTCs set?
Yes : Refer to
No : Go to Step 3.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-29
STEP 3. Using scan tool MB991958, read the MFI system
diagnostic trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch "ON" position.
(3) Read the diagnosis code.
Q: Have any MFI system DTCs set?
Yes : Refer to GROUP 13A, MFI Diagnosis
− Diagnostic
or GROUP 13B, MFI
Diagnosis
− Diagnostic Trouble Code Chart
No : Go to Step 4.
STEP 4. Attempt to start the engine.
Q: Does the engine start?
YES : The procedure is complete (If no malfunctions are
found in all steps, an intermittent malfunction is
suspected. Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points-How to
Cope with Intermittent Malfunction
NO : Refer to GROUP 13A, MFI Diagnosis
− Symptom
Chart
−
. If the malfunction is not
resolved, replace the immobilizer-ECU. Then register
the password (secret code) and encrypted code.
(Refer to
.) The engine should now start.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-30
INSPECTION PROCEDURE 4: The Immobilizer Indicator Light does not Illuminate.
BATTERY
RELAY
BOX
JOINT
CONNECTOR (1)
COMBINATION
METER
IMMOBILIZER
-ECU
IMMOBILIZER
Immobilizer Indicator Light Circuit
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-31
.
CIRCUIT OPERATION
If the requirements for starting the engine are not sat-
isfied, the immobilizer-ECU flashes the immobilizer
indicator for 30 seconds.
.
TECHNICAL DESCRIPTION (COMMENT)
The immobilizer indicator light or a malfunction of the
combination meter or immobilizer-ECU.
.
TROUBLESHOOTING HINTS
• Malfunction of combination meter
• Malfunction of immobilizer-ECU
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
.
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Check immobilizer-ECU connector C-124 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector
Q: Is immobilizer-ECU connector C-124 in good condition?
YES : Go to Step 2.
NO : Repair or replace the component(s). Refer to GROUP
00E, Harness Connector Inspection
. Confirm
that scan tool MB991958 communicates normally.
AC305231
C-29
CONNECTORS: C-01, C-29, C-101, C-124
C-01
C-124
C-101
CU
AC305231CQ
CONNECTOR: C-124
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст