Mitsubishi Galant 9G. Manual — part 1171
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-984
STEP 5. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2138 set?
YES : Replace the PCM. Then go to Step 16.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
STEP 6. Check the continuity at accelerator pedal position
sensor harness side connector C-24.
(1) Disconnect the connector C-24 and measure at the harness
side.
(2) Measure the continuity between terminal No. 5 and ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 10.
NO : Go to Step 7.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303202
1
6 5 4 3 2
ACCELERATOR
PERAL
AB
CONNECTOR: C-24
C-24 (B)
ACCELERATOR
PEDAL POSITION
SENSOR
HARNESS
CONNECTOR:
COMPONENT SIDE
1
6 5 4 3 2
AK303207
C-24 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-985
STEP 7. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 16.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-986
STEP 8. Check for harness damage between accelerator
pedal position sensor connector C-24 (terminal No. 5) and
PCM connector B-20 (terminal No. 22).
Q: Is the harness wire in good condition?
YES : Go to Step 9.
NO : Repair it. Then go to Step 16.
AK303202
1
6 5 4 3 2
ACCELERATOR
PERAL
AB
CONNECTOR: C-24
C-24 (B)
ACCELERATOR
PEDAL POSITION
SENSOR
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-987
STEP 9. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P2138 set?
YES : Replace the PCM. Then go to Step 16.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
STEP 10. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 16.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст