Mitsubishi Galant 9G. Manual — part 1260
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-144
STEP 28. Check the CAN_H line (communication line only)
between the powertrain control module connector and
ABS-ECU connector for a short to the power supply.
Measure voltage at powertrain control module connector
B-19.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect powertrain control module connector B-19 and
ABS-ECU connector A-02, and measure the voltage at the
harness side of powertrain control module connector B-19.
(2) Turn the ignition switch to the "ON" position.
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
AC306248AD
B-19 (B)
CONNECTOR: B-19
PCM
AIR
CLEANER
HARNESS SIDE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-145
(3) Measure the voltage between powertrain control module
connector terminal 17 and body ground.
OK: 1.0 V or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Does the voltage measure 1.0 V or less?
YES : If the voltage measures 1.0 V or less, go to Step 29.
NO : If the voltage measures more than 1.0 V, repair the
wiring harness between powertrain control module
connector and ABS-ECU connector.
STEP 29. Check the CAN_H line inside the ABS-ECU for a
short to the power supply. Measure the voltage at
ABS-ECU connector A-02.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect ABS-ECU connector A-02.
AC209365
AC209365
AC209365FZ
HARNESS SIDE: B-19
TEST
HARNESS
AC305206
CONNECTOR: A-02
AG
A-02 (GR)
HARNESS SIDE
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-146
(2) Connect special tool MB991970 (ABS check harness) to
the ABS-ECU and the wiring harness, and measure the
voltage at special tool MB991970 (ABS check harness).
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between special tool MB991970 (ABS
check harness) connector terminal 25 and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, diagnose CAN
bus lines thoroughly by referring to
NO : If the voltage measures more than 4.0 V, replace the
ABS-ECU.
STEP 30. Check intermediate connector C-29 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is intermediate connector C-29 in good condition?
YES : Go to Step 31.
NO : Repair the damaged parts.
AC209767
2
19
1
18
25
8
15
16
17
27
28
26
11
9
10
12
13
14
23
24
22 21
7
6
5
4
20
3
TEST
HARNESS
SPECIAL TOOL
MB991970
ABS-
ECU
MEASURE AT THIS CONNECTOR
SPECIAL TOOL MB991970
CONNECTOR
AC
AC305231AI
CONNECTOR: C-29
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-147
STEP 31. Check the CAN_L-side bus line (communication
line including ) of the front wiring harness for a short to the
power supply. Measure the voltage at intermediate
connector C-29.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect intermediate connector C-29, and measure the
voltage at the male side (at front wiring harness side).
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between intermediate connector
terminal 12 and body ground.
OK: 4.0 V or less
Q: Does the voltage measure 4.0 V or less?
YES : If the voltage measures 4.0 V or less, go to Step 32.
NO : If the voltage measures more than 4.0 V, go to Step
AC305231AI
CONNECTOR: C-29
AC209365
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
AC209365
MALE SIDE: C-29
TEST HARNESS
GA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст