Mitsubishi Galant 9G. Manual — part 379
DOOR MIRROR
TSB Revision
EXTERIOR
51-42
REMOVAL SERVICE POINT
.
<<A>> POWER WINDOW SWITCH PANEL
ASSEMBLY REMOVAL
Insert special tool MB990874 as shown to remove the power
window switch panel assembly.
INSPECTION
M1511006500305
ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK
Check that the mirror moves as described in the table when
each terminal is connected to the battery.
REMOTE CONTROLLED MIRROR
REMOVAL STEPS
• FRONT DOOR TRIM (REFER TO
GROUP 52A, DOOR TRIMS
1. DOOR MIRROR COVER
2. REMOTE CONTROLLED MIRROR
ASSEMBLY
REMOTE CONTROLLED MIRROR
SWITCH REMOVAL STEPS
<<A>>
3. POWER WINDOW SWITCH PANEL
ASSEMBLY
4. REMOTE CONTROLLED MIRROR
SWITCH
AC306721
MB990784
POWER WINDOW SWITCH
PANEL ASSEMBLY
AB
BATTERY CONNECTION
DIRECTION
OPERATION
• Connect terminal 6 to the negative
battery terminal.
• Connect terminal 4 to the positive battery
terminal.
Up
• Connect terminal 6 to the positive battery
terminal.
• Connect terminal 4 to the negative
battery terminal.
Down
• Connect terminal 6 to the negative
battery terminal.
• Connect terminal 5 to the positive battery
terminal.
Right
• Connect terminal 6 to the positive battery
terminal.
• Connect terminal 5 to the negative
battery terminal.
Left
AC307166
DOOR MIRROR
TSB Revision
EXTERIOR
51-43
DOOR MIRROR CONTROL SWITCH CONTINUITY
CHECK
SWITCH POSITION TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
9
− 2, 9 − 3, 9 − 6,
9
− 10, 9 − 11, 1 − 2,
1
− 3, 1 − 6, 1 − 10,
1
− 11
Open circuit
Left side
OFF
9
− 6, 9 − 10, 9 − 11,
1
− 6, 1 − 10, 1 − 11
Open circuit
Up
1
− 6, 9 − 11
Less than 2
ohms
Down
1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right side OFF
9
− 2, 9 − 3, 9 − 6,
1
− 2, 1 − 3, 1 − 6
Open circuit
Up
1
− 6, 3 − 9
Less than 2
ohms
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
AC005970
2
1
4
3
5
10
9
8
7
6
11
DOOR MIRROR
TSB Revision
EXTERIOR
51-44
HEATED DOOR MIRROR CHECK
CAUTION
When relocating the car between locations with extremely
different temperatures (warm and cold), leave the car in
the location for a while to adapt to the temperature prior to
checking it.
Check to see that the resistance shown in the graph is almost
satisfied when measuring the resistance of terminal 1 and 3 of
the door mirror connectors.
AC307177
RESISTANCE
TEMPERATURE (˚C)
-10
0
10
20
30
40
(
Ω)
0
2
4
6
8
10
AB
12
UPPER LIMIT VALUE
LOWER LIMIT VALUE
SPECIFICATIONS
TSB Revision
EXTERIOR
51-45
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1511015300279
SERVICE SPECIFICATIONS
M1511000300358
ADHESIVE
M1511000500448
ITEM
SPECIFICATION
Front bumper
License plate screw
0.9
± 0.1 N⋅m (8 ± 1 in-lb)
Windshield wiper and washer
Wiper arm and blade assembly nut
25
± 3.0 N⋅m (18 ± 1 ft-lb)
Wiper link assembly bolt
4.9
± 0.5 N⋅m (43 ± 4 in-lb)
Wiper motor screw
7.5
± 1.4 N⋅m (66 ± 13 in-lb)
Washer tank bolt
12
± 1.0 N⋅m (102 ± 15 in-lb)
Door mirror
Remote controlled mirror assembly bolt
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
ITEM
STANDARD VALUE
Windshield wiper blade (RH) park position
38
± 5 mm (1.50 ± 0.20 inches)
Windshield wiper blade (LH) park position
38
± 5 mm (1.50 ± 0.20 inches)
ITEM
SPECIFICATION
Door side protector molding
Adhesive tape: Double-sided tape
8.0 mm (0.32 inch) width and 1.2 mm (0.05 inch)
thickness
Roof drip molding
Adhesive tape: Double-sided tape
10.0 mm (0.39 inch) width and 1.52 mm (0.06 inch)
thickness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст