Mitsubishi Galant 9G. Manual — part 1044
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-476
(4) Measure the voltage between terminal No. 41 and ground.
• Voltage should be between 4.5 and 4.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.5 and 4.9 volts?
YES : Go to Step 6.
NO : Go to Step 7.
STEP 6. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Check harness connector C-25 at intermediate
connector for damage, and repair or replace as
required. Refer to GROUP 00E, Harness Connector
Inspection
. If the intermediate connector is in
good condition, repair the harness wire between fuel
tank temperature sensor connector D-18 and PCM
connector B-20 because of open circuit. Then go to
Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
AK203168AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-477
STEP 7. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
STEP 8. Check the continuity at fuel tank temperature
sensor harness side connector D-18.
(1) Disconnect the connector D-18 and measure at the harness
side.
(2) Check for the continuity between terminal No. 1 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 9.
NO : Repair harness wire between fuel tank temperature
sensor connector D-18 (terminal No. 1) and ground
because of open circuit or harness damage. Then go
to Step 11.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
3
4
5
AK303090
D-18 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-478
STEP 9. Check harness connector B-20 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 11.
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-479
STEP 10. Check for open circuit and harness damage
between fuel tank temperature sensor connector D-18 and
PCM connector B-20.
NOTE: Check harness after checking intermediate connector
C-25. If the intermediate connector is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion
. Then go to Step 11.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст