Mitsubishi Galant 9G. Manual — part 899
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-1038
(3) Measure the voltage between terminal No. 132 and ground.
NOTE: Vehicle for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.
a. Engine: warming up
b. Radiator fan: stopped
c. Headlight switch: OFF to ON
d. Rear defogger switch: OFF to ON
e. Stoplight switch: OFF to ON
• Voltage rises.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage within the specified range?
YES : Go to Step 2.
NO : Replace the generator. Then confirm that the
malfunction symptom is eliminated.
STEP 2. Check harness connector B-23 at PCM connector
and harness connector B-116 at generator connector for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then confirm that the
malfunction symptom is eliminated.
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK203183AB
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
AK303884
2
1
3
4
AB
CONNECTOR: B-116
B-116 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-1039
STEP 3. Check for open circuit and short circuit to ground
and harness damage between generator connector B-116
(terminal No. 1) and PCM connector B-23 (terminal No.
132).
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then confirm that the malfunction
symptom is eliminated.
NO : Repair it. Then confirm that the malfunction symptom
is eliminated.
AK303884
2
1
3
4
AB
CONNECTOR: B-116
B-116 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-1040
INSPECTION PROCEDURE 27: Fans (radiator fan, A/C condenser fan) are inoperative
.
COMMENT
• The fan control relay is controlled by the power
transistor inside the PCM turning "ON" and
"OFF".
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Malfunction of the fan control relay.
• Malfunction of the fan condenser fan relay.
• Malfunction of the radiator fan relay.
• Malfunction of the condenser fan motor.
• Malfunction of the radiator fan motor.
• Improper connector contact, open or shorted har-
ness wire.
• PCM failed.
RED-WHITE
AK303260
5
POWERTRAIN
CONTROL
MODULE (PCM)
RADIATOR
FAN RELAY
WHITE-RED
WHITE-RED
CONDENSER
FAN RELAY
BLUE-ORANGE
10
FAN CONTROL
RELAY
B-19
1 2 3 4
5 6 7
8 9 10 11
12 13 14
15 16 17 18
AK303147
CONNECTOR: B-19
PCM
AB
AIR CLEANER
B-19 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-1041
DIAGNOSIS
Required Special Tools:
• MB991958: Scan tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Check harness connector B-19 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then confirm that the
malfunction symptom is eliminated.
STEP 2. Check the fan condition.
(1) Disconnect the B-19 at PCM connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check the fan condition.
• When the terminal No.10 is grounded by the jumper
cable, the radiator and condenser fans should run.
• When the terminal No.10 is grounded first and then both
of the terminal No.10 and No.5 are grounded next,
check that the rotation speed of fan is higher than the
rotation speed when the terminal No.10 is grounded.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the fan condition normal?
YES : Go to Step 3.
NO : Refer to GROUP 14, Symptom Chart
AK303153
4 3 2 1
7 6 5
9 8
11 10
14 13 12
18 17 16 15
CONNECTOR: B-19
PCM
AB
AIR CLEANER
HARNESS CONNECTOR:
COMPONENT SIDE
B-19 (B)
AK303257
1 2 3 4
5 6 7
8 9 10 11
12 13 14
15 16 17 18
B-19 HARNESS CONNECTOR:
COMPONENT SIDE
AB
AK303259
1 2 3 4
5 6 7
8 9 10 11
12 13 14
15 16 17 18
B-19 HARNESS CONNECTOR:
COMPONENT SIDE
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст