Mitsubishi Galant 9G. Manual — part 1075
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-600
STEP 3. Check harness connector B-21 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 6.
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-601
STEP 4. Check for open circuit, short circuit to ground and
harness damage between knock sensor connector B-120
(terminal No. 1) and PCM connector B-21 (terminal No. 59).
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it. Then go to Step 6.
AK303120
1
2
KNOCK SENSOR
AB
CONNECTOR: B-120
B-120 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303018
55
56
54 53 52 51
57
62 61 60 59 58
63
69 68 67 66 65 64
70
75 74 73 72 71
76
82 81 80 79 78 77
83
CONNECTOR: B-21
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-602
STEP 5. Check the knock sensor.
(1) Disconnect the knock sensor connector B-120.
(2) Start the engine and run at idle.
(3) Measure the voltage between knock sensor side connector
terminal No. 1 (output) and No. 2 (ground).
(4) Gradually increase the engine speed.
• The voltage increases with the increase in the engine
speed.
(5) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : Replace the PCM. Then go to Step 6.
NO : Replace the knock sensor. Then go to Step 6.
AK303120
1
2
KNOCK SENSOR
AB
CONNECTOR: B-120
B-120 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303857
1 2
AB
KNOCK SENSOR
CONNECTOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-603
STEP 6. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Erase the DTC.
(4) Test drive under the following conditions:
• Engine speed: 3000 − 5000r/min
• Engine load: 40% or more
• Drive a minimum of 3 seconds after the above condi-
tions have been met.
(5) After completing the test drive, read the DTC.Turn the
ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0325 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст