Mitsubishi Galant 9G. Manual — part 439
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-24
STEP 5. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Use scan tool MB991958 to read the TCL diagnostic trouble
).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is DTC U1120 set?
YES : Replace the hydraulic unit (integrated with
ABS/TCL-ECU). (Refer to GROUP 35B
− Hydraulic
Unit
NO : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
STEP 6. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Use scan tool MB991958 to read the TCL diagnostic trouble
).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Disconnect scan tool MB991958.
Q: Is DTC U1120 set?
YES : Return to Step 1.
NO : The procedure is complete.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-25
U1400 Dynamic range error APS1
.
DTC SET CONDITION
This code is set when the MFI system sets either of
DTCs P2138, P2122 or P2123.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THESE DTCS ARE
TO SET ARE:)
• Malfunction of the MFI system
DIAGNOSIS
Check whether the MFI system sets either of diagnostic trouble
codes P2138, P2122 or P2123, and repair if necessary. (Refer
to GROUP 13B, MFI Diagnosis
− Diagnostic Function − How to
Read and Erase Diagnostic Trouble Code
SYMPTOM CHART
M1136003400029
SYMPTOM
INSPECTION
PROCEDURE NO.
REFERENCE
PAGE
Communication with
scan tool is not
possible
Communication with all systems is
impossible
-
Group 13B, MFI
Diagnosis
−
Symptom
Procedures
−
Inspection
Procedure 1
Communication with the ABS/TCL-ECU
only is impossible
-
Group 35B, ABS
Diagnosis
−
Symptom
Procedures
−
Inspection
Procedure 1
.
When the ignition switch is turned to the "ON" position (engine
stopped), the "TCL OFF" indicator light dose not illuminate.
1
When the ignition switch is turned to the "ON" position (engine
stopped), the TCL work indicator light dose not illuminate.
2
The "TCL OFF" indicator light remains illuminated after the engine
is started.
3
The TCL work indicator light remains illuminated after the engine
is started.
4
When the TCL switch is push on, TCL does not be cancelled.
5
TCL dose not operate.
6
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-26
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: When the Ignition Switch is Turned to the "ON" Position
(Engine Stopped), the "TCL OFF" Indicator Light dose not Illuminate. INSPECTION
PROCEDURE 2: When the Ignition Switch is Turned to the "ON" Position (Engine
Stopped), the TCL Work Indicator Light dose not Illuminate. INSPECTION
PROCEDURE 3: The "TCL OFF" Indicator Light Remains Illuminated After the Engine
is Started. INSPECTION PROCEDURE 4: The TCL Work Indicator Light Remains
Illuminated After the Engine is Started.
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
13D-27
BATTERY
IGNITION SWITCH (IG1)
JOINT
CONNECTOR (1)
JOINT
CONNECTOR (3)
RELAY
BOX
JUNCTION
BLOCK
COMBINATION
METER
JOINT
CONNECTOR (4)
ABS/TCL-ECU
AC307013
"TCL OFF" Indicator Light and TCL Work Indicator Light Drive Circuit
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст