Mitsubishi Galant 9G. Manual — part 26
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-100
STEP 7. Check the wiring harness between sunroof motor
assembly connector D-04 (terminal 5) and ground.
Q: Is the wiring harness between sunroof motor assembly
connector D-04 (terminal 5) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The system
should communicate with the sunroof-ECU normally.
STEP 8. Check ETACS-ECU connector C-218 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-218 in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The system should communicate with the
sunroof-ECU normally.
STEP 9. Check the wiring harness between sunroof motor
assembly connector D-04 (terminal 10) and ETACS-ECU
connector C-218 (terminal 59).
AC400530
AI
CONNECTOR: D-04
HARNESS SIDE
AC305413AN
CONNECTOR: C-218
JUNCTION BLOCK
(REAR VIEW)
C-218 (GR)
HARNESS SIDE
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
AC305413AN
CONNECTOR: C-218
JUNCTION BLOCK
(REAR VIEW)
C-218 (GR)
HARNESS SIDE
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
AC400530
AI
CONNECTOR: D-04
HARNESS SIDE
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-101
NOTE: Also check intermediate connector C-27 and joint con-
nector C-03 for loose, corroded, or damaged terminals, or ter-
minals pushed back in the connector. If intermediate connector
C-27 or joint connector C-03 is damaged, repair or replace the
damaged component(s) as described in GROUP 00E, Harness
Connector Inspection
.
Q: Is the wiring harness between sunroof motor assembly
connector D-04 (terminal 10) and ETACS-ECU connector
C-218 (terminal 59) in good condition?
YES : Go to Step 10.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The system
should communicate with the sunroof-ECU normally.
STEP 10. Replace the sunroof motor assembly.
(1) Replace the sunroof motor assembly.
(2) The system should communicate with the sunroof-ECU
normally.
Q: Can the system communicate with the sunroof-ECU?
YES : No action is necessary and testing is complete.
NO : Replace the ETACS-ECU. The system should
communicate with the sunroof-ECU normally.
TONE ALARM
GENERAL DESCRIPTION CONCERNING THE TONE ALARM
M1549021000326
The tone alarm functions are as follows. These func-
tions are controlled by relevant ECUs.
AC305232
AC305232
CONNECTORS: C-03, C-27
AI
C-03
C-27
C-27
C-03 HARNESS SIDE
FUNCTION
CONTROL ECU
Ignition key reminder tone alarm function
ETACS-ECU
Light reminder tone alarm function
ETACS-ECU, column switch
Seat belt tone alarm function
ETACS-ECU
Door ajar warning buzzer
ETACS-ECU
Center display operation tone <vehicles with multi center
display (middle-grade type)>
ETACS-ECU
Turn-signal light buzzer
ETACS-ECU, column switch
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-102
Ignition key reminder tone alarm function
When the driver’s door is opened with the ignition key inserted
in the ignition key cylinder (ignition switch is in the OFF posi-
tion,) the tone alarm sounds intermittently to indicate that the
ignition key has not been removed.
Light reminder tone alarm function
When the taillights or headlights is the ON position, if the igni-
tion key is removed and the driver's door is opened, a tone
alarm will sound continuously to warn that the lights are on.
However, if the taillights or headlights have been turned off by
the headlight automatic-shutoff function, the tone alarm will not
sound.
Seat belt tone alarm function
AC005427AB
ON
OFF
ON
(Key removed)
OFF
(Key inserted)
ON (Open)
OFF (Closed)
ON (Tone alarm
sounds)
OFF (Tone alarm
does not sound)
Ignition switch
(IG1)
Key
reminder
switch
Driver's
door
switch
Ignition key
inserted
reminder
tone alarm
output
AC005428
AB
ON
OFF
ON
(Key removed)
OFF
(Key inserted)
ON (Open)
OFF (Closed)
ON (Tone alarm
sounds)
OFF (Tone alarm
does not sound)
Tail light or
headlight
Key
reminder
switch
Driver's
door
switch
Light
reminder
tone
alarm output
AC305326 AC
ON
OFF
ON (UNFASTENED)
OFF (FASTENED)
ON (TONE ALARM SOUNDS)
OFF (TONE ALARM DOES
NOT SOUND)
IGNITION SWITCH (IG1)
SEAT BELT
TONE ALARM
OUTPUT
T
T
T
T
T
T: 6 SECONDS
T1: 1 SECOND
T
T1
t t t
T1
T1
T1
T1
T1
t1
t: 0.16 SECOND
t1: 0.52 SECOND
SEAT BELT
TONE ALARM
OUTPUT
ON (TONE ALARM
SOUNDS)
OFF (TONE ALARM
DOES NOT SOUND)
SEAT BELT SWITCH
(DRIVER'S SIDE)
T
SYMPTOM PROCEDURES
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-103
If any of the following conditions is met with the igni-
tion switch at "ON" or "ST", the ETACS-ECU sounds
the tone alarm by using the driver's seat belt switch
signal and the vehicle speed signal sent from the
combination meter.
• Sounds the tone alarm for six seconds when the
ignition switch is turned "ON" with the seat belt
switch on (the driver's seat belt is not fastened).
This is called "Timer function".
• Sounds the tone alarm 12 cycles (after 0.5 sec-
onds) if any of the following conditions is met
when sixty seconds or more have elapsed since
the ignition switch is turned "ON". One cycle con-
sists of five-second "on" and then three-second
"off".
a. The vehicle speed has reached 8 km/h (5
mph) while the seat belt switch is turned on
(driver's seat belt is not fastened) with the
ignition switch "ON.
b. The seat belt switch has been turned on
(driver's seat belt has not been fastened) for
at least ten seconds while the ignition switch
has been turned "ON" and the vehicle speed
has been 8 km/h (5 mph) or more.
NOTE: Once the tone alarm has sounded 12
cycles, it does not sound again until the vehi-
cle speed reduces to 3 km/h (2 mph) or less
even if any of the following conditions is met.
• The tone alarm stops sounding if the ignition
switch or the seat belt switch is turned off (the
driver's seat belt is fastened) while the timer
operation is active.
AC305374
ON
OFF
ON (UNFASTENED)
OFF (FASTENED)
ON (TONE ALARM
SOUNDS)
IGNITION SWITCH (IG1)
SEAT BELT
SWITCH
(DRIVER'S SIDE)
SEAT BELT
TONE ALARM
OUTPUT
a: 0.5 SECOND
b: 5 SECONDS
c: 3 SECONDS
d: 60 SECONDS OR MORE
8 km/h (5 mph)
0 km/h (0 mph)
VEHICLE SPEED
d
e: 10 SECONDS
AC
3 km/h (2 mph)
T: 6 SECONDS
T1: 1 SECOND
t: 0.16 SECOND
t1: 0.52 SECOND
b
T1
t t t
T1
T1
T1
T1
t1
SEAT BELT
TONE ALARM
OUTPUT
ON (TONE ALARM
SOUNDS)
OFF (TONE ALARM
DOES NOT SOUND)
OFF (TONE ALARM
DOES NOT SOUND)
T
b
b
c
c
a
a
a
12 CYCLES
1 CYCLE
e
12 CYCLES
12 CYCLES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст