Mitsubishi Galant 9G. Manual — part 1216
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1164
INJECTOR
Required Special Tools:
• MB991658: Test Harness
• MB991923: Power Plant ECU Check Harness
.
Measurement Method
<Measure at the right bank (number 1, 3, 5 cylinders)>
1. Disconnect the intermediate connector B-32, and connect
the test harness special tool (MB991658) between the
separated connector.
2. Connect the oscilloscope probe to each intermediate
connector B-32 terminal to analyze each cylinder:
• Terminal No. 5 for the number 1 cylinder
• Terminal No. 10 for the number 3 cylinder
• Terminal No. 4 for the number 5 cylinder
<Measure at the right bank (number 2, 4, 6 cylinders)>
1. Disconnect the injector connector, and connect the test har-
ness special tool (MB991658) between the separated con-
nector. (All terminals should be connected.)
2. Connect the oscilloscope probe to injector connector termi-
nal No. 2.
Alternate method (Measure at the PCM)
1. Disconnect the all PCM connectors, and connect check har-
ness special tool (MB991923) between the separated con-
nectors.
1
2 3
6
7 8
4 5
9 10
AK203300
OSCILLOSCOPE
MB991658
B-32 INTERMEDIATE
CONNECTOR
AB
AK302166
1 2
INJECTOR
CONNECTOR
MB991658
OSCILLOSCOPE
AB
AK202954
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1165
2. Connect the oscilloscope probe to each check harness con-
nector terminal to analyze each cylinder:
• Terminal No. 153 for the number 1 cylinder.
• Terminal No. 146 for the number 2 cylinder.
• Terminal No. 140 for the number 3 cylinder.
• Terminal No. 139 for the number 4 cylinder.
• Terminal No. 133 for the number 5 cylinder.
• Terminal No. 127 for the number 6 cylinder.
Standard Wave Pattern
Wave Pattern Observation Points
Point A: Height of injector coil induced voltage.
Observation conditions
Function
Special pattern
Pattern height
Variable
Variable knob
Adjust while viewing the
wave pattern
Pattern selector
Display
Engine r/min
Idle speed
CONTRAST WITH
STANDARD WAVE
PATTERN
PROBABLE CAUSE
Injector coil induced voltage is
low or doesn't appear at all
Short in the injector solenoid
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303185AB
OSCILLOSCOPE
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
AKX01604
(V)
50
0
DRIVE SIGNAL:"ON"
POINT B:
INJECTOR DRIVE
TIME
POINT A
DRIVE SIGNAL:"OFF"
POWER VOLTAGE
INJECTION COIL INDUCED
VOLTAGE (APPROXIMATELY 50-60 V)
AB
Standard wave pattern
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1166
Point B: Injector drive time
1. The injector drive time should be synchronized with the
scan tool tester display.
2. When the engine is suddenly revved, the drive time will be
greatly extended at first, but the drive time will soon return
to original length.
EGR VALVE (STEPPER MOTOR)
Required Special Tools:
• MB991658: Test Harness
• MB991923: Power Plant ECU Check Harness
.
Measurement Method
1. Disconnect the EGR valve connector, and connect the test
harness special tool (MB991658) between the separated
connector (All terminals should be connected).
2. Connect the oscilloscope probe to the EGR valve connector
terminal No. 1, terminal No. 3, terminal No. 4, terminal No. 6
respectively.
.
Alternate method (Measure at the PCM)
1. Disconnect the all PCM connectors, and connect check
harness special tool (MB991923) between the separated
connectors.
AKX01605
WHEN IDLING
WHEN RACING
AB
AK203303
1
2 3
4
5 6
EGR VALVE
CONNECTOR
OSCILLOSCOPE
MB991658
AB
AK202954
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AB
POWER PLANT ECU
CHECK HARNESS CONNECTOR
MB991923
PCM
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-1167
2. Connect the oscilloscope probe to check harness terminal
No. 124, No. 130, No. 136 and No. 142.
Standard Wave Pattern
Wave Pattern Observation Points
1. Check that the standard wave pattern appears when the
EGR valve is operating.
Point A: Presence or absence of induced electromotive force
from the motor turning. (Refer to abnormal wave pattern.)
Point B: Height of coil back electromotive force
.
Observation condition
Function
Special pattern
Pattern height
High
Pattern selector
Display
Engine condition
Revving
CONTRAST WITH
STANDARD WAVE
PATTERN
PROBABLE CAUSE
Induced electromotive force
does not appear or is
extremely small
Malfunction of motor
CONTRAST WITH
STANDARD WAVE
PATTERN
PROBABLE CAUSE
Coil reverse electromotive
force does not appear or is
extremely small
Short in the coil
AK203304
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AB
OSCILLOSCOPE
POWER PLANT ECU
CHECK HARNESS
CONNECTOR
AKX01607 AC
(V)
30
20
10
0
EGR VALVE
(STEPPER
MOTOR)
CONTROL
SIGNAL
WAVE
PATTERN
THE WAVE PATTERN
APPEARS FOR AN
INSTANT, BUT SOON
DISAPPEARS.
POINT B COIL RE-
VERSE ELECTRO-
MOTIVE FORCE
(APPROXIMATELY
3 x10 V)
POINT AN INDUCED
ELECTROMOTIVE
FORCE FROM THE
MOTOR TURNING
TIME
Standard wave pattern
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст