Mitsubishi Galant 9G. Manual — part 706
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-266
STEP 13. Check for short circuit to ground and harness
damage between cylinder 1, 4 heated oxygen sensor (rear)
connector B-38 (terminal No. 4) and PCM connector B-22
(terminal No. 97).
Q: Is the harness wire in good condition?
YES : Go to Step 14.
NO : Repair it. Then go to Step 15.
AK303826
1
2
3
4
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-38
B-38 (B)
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (REAR)
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-267
STEP 14. Check the cylinder 1, 4 heated oxygen sensor
(rear).
(1) Disconnect the cylinder 1, 4 heated oxygen sensor (rear)
connector B-38 and connect test harness special tool
MD998464 to the connector on the cylinder 1, 4 heated
oxygen sensor (rear) side.
(2) Warm up the engine until engine coolant temperature
reaches 80
°C (176°F) or higher.
(3) Perform a racing for 5 minutes or more with the engine
speed of 4,500 r/min.
(4) Connect a digital voltage meter between terminal No. 2
(black clip) and terminal No. 4 (white clip).
(5) While repeatedly revving the engine, measure the cylinder
1, 4 heated oxygen sensor (rear) output voltage.
Standard value: 0.6
− 1.0 volt
CAUTION
• Be very careful when connecting the jumper wire;
incorrect connection can damage the heated oxygen
sensor.
• Be careful the heater is broken when voltage of beyond
12 volts is applied to the heated oxygen sensor heater.
NOTE: If the sufficiently high temperature [of approximate
400
°
C (752
°
F) or more] is not reached although the heated
oxygen sensor is normal, the output voltage would be possi-
bly low although the rich air/fuel ratio. Therefore, if the out-
put voltage is low, use a jumper wire to connect the terminal
No. 1 (red clip) and the terminal No. 3 (blue clip) of the
heated oxygen sensor with the positive terminal and the
negative terminal of 12 volts power supply respectively,
then check again.
Q: Is the measured voltage between 0.6 and 1.0 volt?
YES : Replace the PCM. Then go to Step 15.
NO : Replace the cylinder 1, 4 heated oxygen sensor
(rear). Then go to Step 15.
AK303826
1
2
3
4
AB
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-38
B-38 (B)
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (REAR)
AKX01624
HEATED
OXYGEN
SENSOR
COMPONENT
SIDE
CONNECTOR
MD998464
WHITE
BLACK
AL
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-268
STEP 15. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0136 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0137: Cylinder 1, 4 Heated Oxygen Sensor Circuit Low Voltage (sensor 2)
52
51
53 54 55 56
57
58 59 60 61 62
63
64 65 66 67 68 69
70
71 72 73 74 75
76
77 78 79 80 81 82
83
100
99
92
91
93 94 95
96 97 98
101 102 103 104
105 106 107 108
109 110 111 112 113
AK303824
1
2
3
4
YELLO
W
BLUE
BLA
CK
BLA
CK
TO PCM
FROM MFI RELAY
69
97
2
4
3
1
B-22
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (REAR)
POWERTRAIN CONTROL
MODULE (PCM)
B-38
MU802605
Cylinder 1, 4 Heated Oxygen Sensor (rear) Circuit
B-21
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-269
.
CIRCUIT OPERATION
• A voltage corresponding to the oxygen concen-
tration in the exhaust gas is sent to the PCM (ter-
minal No. 97) from the output terminal (terminal
No. 4) of the cylinder 1, 4 heated oxygen sensor
(rear).
• Terminal No. 2 of the cylinder 1, 4 heated oxygen
sensor (rear) is grounded with PCM (terminal No.
69).
.
TECHNICAL DESCRIPTION
• The output signal of the cylinder 1, 4 heated oxy-
gen sensor (front) is compensated by the output
signal of the cylinder 1, 4 heated oxygen sensor
(rear).
• The PCM checks for an open circuit in the cylin-
der 1, 4 heated oxygen sensor (rear) output line.
.
DESCRIPTIONS OF MONITOR METHODS
Cylinder 1, 4 heated oxygen sensor (rear) output
voltage stays low when air/fuel ratio is forced to
be rich. The above procedure is repeated when
oxygen sensor is inactive.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Heated oxygen sensor heater (front) monitor
• Heated oxygen sensor heater (rear) monitor
• Air/fuel ratio feedback monitor
Sensor (The sensor below is determined to be
normal)
• Mass airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
• Barometric pressure sensor
.
AK303825AB
CONNECTOR: B-38
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (REAR)
B-38 (B)
AK303013
CONNECTORS: B-21, B-22
PCM
AB
AIR CLEANER
B-22 (B)
B-21 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст