Mitsubishi Galant 9G. Manual — part 1493
SEAT BELTS WITH PRE-TENSIONER
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-382
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
WARNING
Dispose of seat belt pre-tensioner only according to
the specified procedure. (Refer to
1. When installing the new seat belt pre-tensioner, refer to
“INSPECTION” (
2. Connect the negative (
−) battery cable.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
3. Connect scan tool MB991958 to the data link connector.
4. Turn the ignition switch to the “ON” position.
5. Check DTCs using scan tool MB991958 to ensure entire
SRS operates properly.
At this time, check that no DTC except 26 and 28 are set.
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work. (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
6. Turn the ignition switch to the "LOCK" (OFF) position.
Disconnect the negative (
−) battery cable and tape the
terminal to prevent accidental connection and seat belt
pre-tensioner operation.
.
>>B<< PRE-TENSIONER CONNECTOR
CONNECTION
Connect the pretensioner connector then securely lock the
locking button of the harness-side connector.
.
>>C<< POST-INSTALLATION INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to the “ON” position.
3. Does the "SRS" warning light illuminate for approximately
seven seconds, and go out?
4. If yes, the SRS system is functioning properly. If not, refer to
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC206181
SRS WARNING LIGHT
AB
SEAT BELTS WITH PRE-TENSIONER
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-383
INSPECTION
M1524004200256
.
SEAT BELT WITH PRE-TENSIONER CHECK
WARNING
•
If any component damage is found during the fol-
lowing inspection, replace the seat belt with
pre-tensioner with a new one. Dispose of the old
one according to the specified procedure. (Refer to
•
Never attempt to measure the circuit resistance of
the seat belt pre-tensioner even if you are using
the specified tester. If the circuit resistance is mea-
sured with a tester, accidental seat belt pre-ten-
sioner operation will result in serious personal
injury.
1. Check seat belt pre-tensioner for dents, cracks or
deformation.
2. Check the connectors for damage, the terminals for
deformation, and the harness for binding.
SEAT SLIDE SENSOR
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-384
SEAT SLIDE SENSOR
M1524025300010
REMOVAL AND INSTALLATION
WARNING
•
Never attempt to disassemble or repair the seat slide sensor. If faulty, replace it.
•
Do not drop or subject the seat slide sensor to impact or vibration. Replace the seat slide
sensor, if dents, cracking, deformation, or rust are present.
Pre-removal Operation
• Turn the ignition key to the "LOCK" (OFF) position.
AC307471AB
FRONT SEAT ASSEMBLY
2
5.0 ± 1.0 N·m
44 ± 9 in-lb
1
SLIDE ADJUSTER
REMOVAL STEPS
<<A>>
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTION
•
FRONT SEAT <DRIVER’S SIDE>
(REFER TO GROUP 52A, FRONT
SEAT ASSEMBLY
2.
SEAT SLIDE SENSOR
INSTALLATION STEPS
>>A<<
•
PRE-INSTALLATION INSPECTION
>>B<<
2.
SEAT SLIDE SENSOR
•
FRONT SEAT <DRIVER’S SIDE>
(REFER TO GROUP 52A, FRONT
SEAT ASSEMBLY
1.
NEGATIVE (
−) BATTERY CABLE
CONNECTOR
>>C<<
•
POST-INSTALLATION
INSPECTION
SEAT SLIDE SENSOR
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-385
REMOVAL SERVICE POINT
.
<<A>> NEGATIVE (
−) BATTERY CABLE DISCON-
NECTION
DANGER
Wait at least 60 seconds after disconnecting the bat-
tery cable before doing any further work. (Refer to
).
WARNING
Battery posts, terminals and related accessories con-
tain lead and lead compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative (
−) battery cable from the battery and
tape the terminal to prevent accidental connection and air bag
deployment.
INSTALLATION SERVICE POINTS
.
>>A<< PRE-INSTALLATION INSPECTION
Check the seat slide sensor for dents, breakage and bending
and measure the resistance between the terminals, even when
installing a new seat slide sensor.
.
ACX00583
INSULATING TAPE
BATTERY
BATTERY CABLE (–)
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст