Mitsubishi Galant 9G. Manual — part 1430
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-130
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Go to Step 3.
NO : There is an intermittent malfunction such as poor
engaged connector(s) or open circuit (Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
− How to Cope with Intermittent
Malfunctions ).
STEP 3. Check the side-airbag module (RH). (Using scan
tool MB991958, read the diagnostic trouble code.)
(1) Disconnect the negative battery terminal.
(2) Disconnect the side-airbag module (RH) connector D-32.
(3) Connect special tool MB991865 to special tool MB991866.
CAUTION
Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(4) Insert special tool MB991866 into the D-32 harness side
connector by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnostic trouble code memory, and check the
diagnostic trouble code.
Q: Is DTC B1421 set?
YES : Go to Step 4.
NO : Replace the seatback frame of the front seat (RH)
(Refer to GROUP 52A, Front Seat
go to Step 5.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC307779
D-32 (R)
AD
2
1
HARNESS SIDE
CONNECTOR
(REAR VIEW)
CONNECTOR : D-32
AC006042BO
MB991866
(RESISTOR HARNESS)
D-32 HARNESS SIDE
CONNECTOR
D-32 SIDE-AIRBAG
MODULE (RH) CONNECTOR
MB991865 (DUMMY
RESISTOR: 3
Ω
)
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-131
STEP 4. Check the harness for open circuit between
SRS-ECU connector C-120 (terminal No.57 and 58) and the
side-airbag module (RH) connector D-32 (terminal No.1
and 2).
(1) Disconnect SRS-ECU connector C-120 and side-airbag
module (RH) connector D-32.
CAUTION
Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(2) Check for continuity between the following terminals. It
should be less than 2 ohms.
• SRS-ECU connector C-120 (terminal No.57) and the
side-airbag module (RH) connector D-32 (terminal No.2)
• SRS-ECU connector C-120 (terminal No.58) and the
side-airbag module (RH) connector D-32 (terminal No.1)
Q: Does continuity exist?
YES : Erase the diagnostic trouble code memory, and check
the diagnostic trouble code. If DTC B1421 sets,
replace the SRS-ECU (Refer to
). Then go
to Step 5.
NO : Replace the harness wires between SRS-ECU
connector C-120 and side-airbag module (RH)
connector D-32. Then go to Step 5.
AC305362
CONNECTOR: C-120
C-120 (Y)
AG
SRS-ECU
63
55
51
69
61
66
58
65
64
56 57
68
60
67
59
70
62
53
52 B
A
54
C-120
Harness side
connector
(rear view)
AC307779
D-32 (R)
AD
2
1
HARNESS SIDE
CONNECTOR
(REAR VIEW)
CONNECTOR : D-32
AC301580
1 2
63
55
51
69
61
66
58
65
64
56 57
68
60
67
59
70
62
53
52 B
A
54
C-120
HARNESS SIDE
CONNECTOR
(REAR VIEW)
D-32
HARNESS SIDE
CONNECTOR
(REAR VIEW)
AC
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-132
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1421 set?
YES : Return to Step 1.
NO : The procedure is complete.
DTC B1422: Side-Airbag Module (RH) (Squib) System Fault Power Supply Circuit (Short-Circuited to
Power Supply)
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SIDE AIR BAG
MODULE
(SQUIB) (RH)
AIR BAG DRIVE CIRCUIT
SRS-ECU
CONNECTOR
LOCK SWITCH
CONNECTOR
LOCK SWITCH
Side-Airbag Module (RH) (Squib) Circuit
NOTE
: CONNECTOR
CONNECTED
: ON
CONNECTOR
DISCONNECTED
: OFF
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-133
CAUTION
If DTC B1422 is set in the combination meter,
always diagnose the CAN bus lines.
.
CIRCUIT OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the left and right side
impact sensors. If the impact is over a predeter-
mined level, the SRS-ECU sends an ignition sig-
nal. At this time, if the side-airbag safing
G-sensor is on, the SRS side-airbag will inflate.
• The ignition signal is input to the side-airbag
module to inflate the side-airbag.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the side-airbag mod-
ule (RH) (squib).
.
TROUBLESHOOTING HINTS
• Damaged wiring harnesses or connectors
• Short to the power supply in the side-airbag mod-
ule (RH) (squib) harness
• Malfunction of the SRS-ECU
.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A (Vehicles with CAN
communication system)
• MB991865: Dummy resistor
• MB991866: Resister harness
AC305362
CONNECTOR: C-120
C-120 (Y)
AC
SRS-ECU
AC307779
D-32 (R)
AC
CONNECTOR : D-32
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст