Mitsubishi Galant 9G. Manual — part 681
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-166
STEP 8. Check for harness damage between throttle
position sensor connector B-06 (terminal No. 5) and PCM
connector B-22 (terminal No. 94).
Q: Is the harness wire in good condition?
YES : Go to Step 9.
NO : Repair it. Then go to Step 11.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-167
STEP 9. Check for open circuit, short circuit to ground and
harness damage between throttle position sensor
connector B-06 (terminal No. 6) and PCM connector B-22
(terminal No. 98).
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 11.
STEP10. Replace the throttle body assembly.
(1) Replace the throttle body assembly.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC P0122 set?
YES : Replace the PCM. Then go to Step 11.
NO : The inspection is complete.
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
AK303818
1
6 5 4 3 2
AB
CONNECTOR: B-06
B-06 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-168
STEP 11. Using scan tool MB991958, read the diagnostic
trouble code (DTC).
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P0122 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK303804AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-169
DTC P0123: Throttle Position Sensor (main) Circuit High Input
CAUTION
If DTC P0123 has been set, TCL related DTC
U1120 is also set. After P0123 has been diag-
nosed, don't forget to erase DTC U1120.
.
6
1 2 3 4 5
100
99
92
91
93 94 95
96 97 98
101 102 103 104
105 106 107 108
109 110 111 112 113
AK400878
YELLO
W
-RED
WHITE-RED
BLA
CK-WHITE
B-06
94
5
THROTTLE POSITION
SENSOR (MAIN)
HALL IC
POWERTRAIN
CONTROL
MODULE (PCM)
98
95
6
3
Throttle Position Sensor (main) Circuit
B-22
5 V
AK303817AB
CONNECTOR: B-06
B-06 (B)
THROTTLE
ACTUATOR
CONTROL
MOTOR
THROTTLE
POSITION
SENSOR
AK303043
CONNECTOR: B-22
B-22 (B)
PCM
AB
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст