Mitsubishi Galant 9G. Manual — part 701
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-246
STEP 8. Check harness connector B-23 at PCM for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 12.
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-247
STEP 9. Check for harness damage between MFI relay
connector B-17X (terminal No. 4) and cylinder 1, 4 heated
oxygen sensor (front) connector B-37 (terminal No. 1).
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 12.
AK303806
2
1
3
4
AB
CONNECTOR: B-17X
B-17X
RELAY BOX
TRIANGLE
MARK
HARNESS CONNECTOR:
COMPONENT SIDE
AK303821
1
2
3
4
AB
CONNECTOR: B-37
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (FRONT)
B-37 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-248
STEP 10. Check for harness damage between cylinder 1, 4
heated oxygen sensor (front) connector B-37 (terminal No.
3) and PCM connector B-23 (terminal No. 126).
Q: Is the harness wire in good condition?
YES : Go to Step 11.
NO : Repair it. Then go to Step 12.
AK303821
1
2
3
4
AB
CONNECTOR: B-37
CYLINDER 1, 4
HEATED OXYGEN
SENSOR (FRONT)
B-37 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
127 126 125 124 123 122 121
133 132 131 130 129 128
140 139 138 137 136 135 134
146 145 144 143 142 141
153 152 151 150 149 148 147
AK303058
HARNESS CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-23
B-23
PCM
AB
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-249
STEP 11. Check the trouble symptoms.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0135 set?
YES : Replace the PCM. Then go to Step 12.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
STEP 12. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0135 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст