Mitsubishi Galant 9G. Manual — part 1453
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-222
STEP 4. Check the harness for open circuit between
SRS-ECU connector C-122 (terminal No.7 and 8) and the
driver's seat belt pre-tensioner D-21 (terminal No.1 and 2).
(1) Disconnect SRS-ECU connector C-122 and driver's seat
belt pre-tensioner connector D-21, and measure at the
wiring harness side. For connector D-21, use a flat-tipped
screwdriver to unlock the locking button at the harness side
connector by withdrawing it toward you in two stages, and
then disconnect the connector.
(2) Connect D-21 harness side connector to special tool
MB991884.
AC305362
CONNECTOR: C-122
C-122 (Y)
AI
SRS-ECU
C-122
Harness side
connector
(rear view)
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
AC306920AC
CONNECTOR: D-21
D-21 (B)
FOWARD
CENTER
PILLAR
HARNESS SIDE
CONNECTOR
(FRONT VIEW)
2 1
AC103556 AT
LOCKING BUTTON
FLAT-TIP SCREW
DRIVER
D-21 HARNESS
SIDE CONNECTOR
D-21 DRIVER'S
SEAT BELT
PRE-TENSIONER
CONNECTOR
AC201287AT
D-21
HARNESS SIDE
CONNECTOR
MB991884
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-223
CAUTION
Do not insert a test probe into the terminal from its front
side directly, as the connector contact pressure may be
weakened.
(3) Check for continuity between the following terminals. It
should be less than 2 ohms.
• SRS-ECU connector C-122 (terminal No.7) and the spe-
cial tool (terminal No.2)
• SRS-ECU connector C-122 (terminal No.8) and the spe-
cial tool (terminal No.1)
Q: Does continuity exist?
YES : Erase the diagnostic trouble code memory, and
recheck if any DTC set. If DTC B1471 set, replace the
SRS-ECU (Refer to
NO : Replace harness wires between SRS-ECU connector
C-122 and driver’s seat belt pre-tensioner connector
D-21. Then go to Step 5.
STEP 5. Check for diagnostic trouble code.
Check again if the DTC is set.
(1) Erase the DTC.
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1471 set?
YES : Return to Step 1.
NO : The procedure is complete.
AC308183
2
1
A
B
18
10
15
7
13
5
14
6
16
8
17
9
19
11
20
12
1 2
3 4
AB
<D-21 HARNESS SIDE
CONNECTOR>
SPECIAL TOOL
MB991884
(FRONT VIEW)
C-122 HARNESS SIDE
CONNECTOR
(REAR VIEW)
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-224
DTC B1472: Seat Belt Pre-Tensioner (LH) (Squib) System Fault for Power Supply Circuit (Short-Circuit
to Power Supply)
CAUTION
If DTC B1472 is set in the SRS-ECU, always diag-
nose the CAN main bus line.
.
CIRCUIT OPERATION
The SRS-ECU judges how severe a collision is by
detecting signals from the front impact sensors and
the front air bag analog G-sensor. If the impact is
over a predetermined level, the SRS-ECU sends an
ignition signal. At this time, if the front air bag safing
G-sensor is on, the pre-tensioner will deploy.
.
DTC SET CONDITIONS
This DTC is set if there is abnormal resistance
between the input terminals of the driver's seat belt
pre-tensioner (squib).
.
TROUBLESHOOTING HITS
• Damaged wiring harnesses or connectors
• Short to the power supply in the driver's seat belt
pre-tensioner (squib) harness
• Malfunction of the SRS-ECU
.
Driver's Seat Belt Pre-Tensioner (Squib) Circuit
SEAT BELT
PRE-TENSIONER
(LH)
PRE-TENSIONER(LH)
DRIVE CIRCUIT
SRS-ECU
CONNECTOR
LOCK SWITCH
CONNECTOR
LOCK SWITCH
: CONNECTOR CONNECTED: ON
CONNECTOR DICONNECTED: OFF
NOTE
AC305362
CONNECTOR: C-122
C-122 (Y)
AE
SRS-ECU
AC306920AB
CONNECTOR: D-21
D-21 (B)
FOWARD
CENTER
PILLAR
SRS AIR BAG DIAGNOSIS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-225
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
• MB991865: Dummy resistor
• MB991884: Resister harness (For Pre-tensioner)
STEP 1. Using scan tool MB991958, diagnose the CAN bus
line.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect the
scan tool
."
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose the CAN bus line.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line (Refer to GROUP 54C,
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст