Mitsubishi Galant 9G. Manual — part 735
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-382
STEP 5. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0157 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
DTC P0158: Cylinder 2, 3 Heated Oxygen Sensor Circuit High Voltage (sensor 2)
52
51
53 54 55 56
57
58 59 60 61 62
63
64 65 66 67 68 69
70
71 72 73 74 75
76
77 78 79 80 81 82
83
100
99
92
91
93 94 95
96 97 98
101 102 103 104
105 106 107 108
109 110 111 112 113
AK303833
1
2
3
4
GREEN
BLUE
BLA
CK
BLA
CK
TO PCM
FROM MFI RELAY
69
96
2
4
3
1
B-22
CYLINDER 2, 3
HEATED OXYGEN
SENSOR (REAR)
POWERTRAIN CONTROL
MODULE (PCM)
B-35
MU802605
Cylinder 2, 3 Heated Oxygen Sensor (rear) Circuit
B-21
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-383
.
CIRCUIT OPERATION
• A voltage corresponding to the oxygen concen-
tration in the exhaust gas is sent to the PCM (ter-
minal No. 96) from the output terminal (terminal
No. 4) of the cylinder 2, 3 heated oxygen sensor
(rear).
• Terminal No. 2 of the cylinder 2, 3 heated oxygen
sensor (rear) is grounded with PCM (terminal No.
69).
.
TECHNICAL DESCRIPTION
• The output signal of the cylinder 2, 3 heated oxy-
gen sensor (front) is compensated by the output
signal of the cylinder 2, 3 heated oxygen sensor
(rear).
• The PCM checks for an open circuit in the cylin-
der 2, 3 heated oxygen sensor (rear) output line.
.
DESCRIPTIONS OF MONITOR METHODS
Cylinder 2, 3 heated oxygen sensor (rear) output
voltage is over specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Heated oxygen sensor heater (front) monitor
• Heated oxygen sensor heater (rear) monitor
• Air/fuel ratio feedback monitor
Sensor (The sensor below is determined to be
normal)
• Mass airflow sensor
• Engine coolant temperature sensor
• Intake air temperature sensor
• Barometric pressure sensor
.
AK303834AB
CONNECTOR: B-35
B-35 (B)
CYLINDER 2, 3
HEATED OXYGEN
SENSOR (REAR)
AK303013
CONNECTORS: B-21, B-22
PCM
AB
AIR CLEANER
B-22 (B)
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-384
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the engine
starting sequence was completed.
Judgment Criteria
• Cylinder 2, 3 heated oxygen sensor (rear) output
voltage has continued to be 1.2 volts or higher for
2 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Short circuit in cylinder 2, 3 heated oxygen sen-
sor (rear) output line.
• Connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
START
END
NO
NO
YES
YES
MALFUNCTION
GOOD
2secs HAVE PASSED?
OUTPUT VOLTAGE > 1.2V
NO
YES
MONITORING
CONDITIONS
AK302026
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L ENGINE>
13A-385
STEP 1. Check harness connector B-35 at cylinder 2, 3
heated oxygen sensor (rear) and harness connector B-22
at PCM for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 3.
AK303835
1
2
3
4
AB
CONNECTOR: B-35
B-35 (B)
CYLINDER 2, 3
HEATED OXYGEN
SENSOR (REAR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303016
104
96
94
95
93 92 91
99 98 97
103 102 101 100
108 107 106 105
113 112 111 110 109
CONNECTOR: B-22
B-22 (B)
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст