Mitsubishi Galant 9G. Manual — part 1601
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-276
5. Choose function button switch 2 ("YES") on the compass
calibration screen.
6. After the message is shown, drive the vehicle in one circle.
7. If the calibration is made successfully, the display unit
buzzer will sound twice.
NOTE: If the calibration fails, a message will appear to indicate
it.
Deflection Angle Compensation
COMPASS CALIBRATION
Under certain circumstances, as during a long distance cross
country trip, it will be necessary to adjust for compass variance.
Compass variance is the difference between earth's magnetic
north and true geographic north.
If not adjusted to account for compass variance, compass
could give false readings.
ADJUST FOR COMPASS VARIANCE
(Compass)
NO
YES
RETURN
Drive vehicle slowly through a 360
Select NO if you do not wish to perfo
turn in a safe, open place.
Select YES if you wish to perform now.
-rm now.
AC208553
AB
(Compass)
Drive vehicle slowly through a 360
turn in a safe, open place.
AC208554AB
AB
AC001243 AB
A002229 AB
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-277
1. Choose "zone code setting" by pressing function button
switch 2 on the compass selection screen, and press
function button switch 3 (ENTER).
2. Find current location and variance zone number on the zone
map.
3. Enter the zone number to calibrate the compass.
4. If the calibration is made successfully, the display unit
buzzer will sound twice.
NOTE: If the calibration fails, a message will appear to indicate
it.
NOTE: Do not install the ski rack, antenna, etc., which are
attached to the vehicle by means of a magnet. They affect the
operation of compass.
NOTE: The compass may not indicate the correct compass
direction in the place shown below:
.
•
Tunnels
•
Railroads
•
Underpass/Overpass
•
Transforming station
•
Large metal structures
•
Area over the subway
Zone code setting
Compass calibration
(Compass)
RETURN
ENTER
AC208552AC
A002229 AB
(Compass)
NO
YES
RETURN
Select correct
zone code
AC209292
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
AB
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-278
VEHICLE MAGNETIC COMPENSATION
M1543009700181
Demagnetization and correction method
1. Demagnetize the body using a commercial demagnetizer.
2. While keeping the distance between the tip of demagnetizer
and the roof panel to approximately 5 cm (2.0 inches), move
the demagnetizer slowly with a sweeping manner on the
rear-half surface of roof panel.
CAUTION
If the tip of demagnetizer touches the roof panel, the mag-
netizing condition of body becomes worse to the contrary.
Absolutely avoid this.
3. Slowly draw the demagnetizer apart from the body. Turn off
the switch of demagnetizer when it is apart from the body
more than 5 cm (2.0 inches).
CAUTION
If the demagnetizer is turned off near the body or it is sud-
denly separated from the body, the magnetizing condition
of body becomes worse to the contrary. Absolutely avoid
these.
AC001246AB
COMMERCIAL DEMAGNETIZER
AC001247
FRONT
DEMAGNETIZER
AB
APPROXIMATELY
5cm(2.0 in)
ROOF PANEL
MULTI-CENTER DISPLAY
TSB Revision
CHASSIS ELECTRICAL
54A-279
CHECK AT MULTI CENTER DISPLAY UNIT TERMINAL
M1543007600519
1
2
11 12
3 4
13 14
5
6
15 16
7
8
17 18
9 10
19 20
C-06
AC210139
1
2
11 12
3 4
13 14
5
6
15 16
7
8
17 18
9 10
19 20
C-06
AC
C-05
C-05
<LOW GRADE TYPE>
<MIDDLE GRADE TYPE>
TERMINAL
NO.
INPUT/
OUTPUT
SIGNAL SYMBOL TERMINAL
VOLTAGE
(V)
HARNESS
DISCREPANCY
FAILURE SYMPTOM DUE TO
HARNESS DISCREPANCY
1
Input
Battery (Battery
power supply)
Battery
positive
voltage
Open
circuit
−
Screen is not displayed. All
operations are not possible.
−
Short
circuit
Fuse is blown.
2
Input
Ignition switch
(IG1)
Battery
positive
voltage
Open
circuit
−
Screen is not displayed. All
operations are not possible.
−
Short
circuit
Fuse is blown.
3
Input
Ignition switch
(ACC)
Battery
positive
voltage
Open
circuit
−
Screen is not displayed. All
operations are not possible.
−
Short
circuit
Fuse is blown.
4
Input
ILL + (lighting
switch)
Hi: Battery
positive
voltage
Lo: 0
− 1
Open
circuit
Short
circuit
Not lighted.
5
Output
ILL - (illumination
light control
signal)
0.4
Open
circuit
Short
circuit
display brightness control is
not possible.
6
−
GND
0
Open
circuit
−
Screen is not displayed.
7 Input/out
put
SB3
−
−
−
−
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст