Mitsubishi Galant 9G. Manual — part 279
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-192
STEP 8. Measure the voltage at A/C compressor assembly
connector B-28.
(1) Disconnect A/C compressor assembly connector B-28 and
measure the voltage at the relay box side.
AC305214
B-28 (B)
HARNESS SIDE
AD
CONNECTOR: B-28 <2.4L>
AC305218
B-28 (B)
HARNESS SIDE
AB
CONNECTOR: B-28 <3.8 L>
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-193
(2) Disconnect powertrain control module connector B-21 and
ground harness side terminal No.81.
(3) Turn the ignition switch to the "ON" position.
(4) A/C compressor assembly connector B-28 terminal 1 and
ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approx. 12 volts?
YES : Go to Step 15.
NO : Go to Step 9.
AC305216
B-21 (B)
AC
CONNECTOR: B-21 <2.4L>
HARNESS SIDE
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
AC305229
B-21 (B)
AB
HARNESS SIDE
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
CONNECTOR: B-21 <3.8 L>
AC306468
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
AC306468
CONNECTOR B-21
(HARNESS SIDE)
AD
AC209365
CONNECTOR B-28
(HARNESS SIDE)
GS
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-194
STEP 9. Measure the voltage at A/C compressor clutch
relay connector B-18X.
CAUTION
The top and bottom of the A/C compressor connector are
difficult to identify. Prior to inspection, confirm the triangle
mark on the relay box.
(1) Disconnect A/C compressor connector B-18X and measure
the voltage at the relay box side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 2 and ground.
• The measured value should be approximately 12 volts
(battery positive voltage).
Q: Is the measured voltage approx. 12 volts?
YES : Go to Step 11.
NO : Go to Step 10.
STEP 10. Check the wiring harness between A/C
compressor clutch relay connector B-18X (terminal 2) and
the ignition switch (IG2).
AC305977AJ
CONNECTOR: B-18X
RELAY BOX SIDE
FRONT OF
VEHICLE
JUNCTION BLOCK
TRIANGLE MARK
AC209365GT
CONNECTOR B-18X
(RELAY BOX SIDE)
AC305977AJ
CONNECTOR: B-18X
RELAY BOX SIDE
FRONT OF
VEHICLE
JUNCTION BLOCK
TRIANGLE MARK
MANUAL A/C DIAGNOSIS
TSB Revision
HEATER, AIR CONDITIONING AND VENTILATION
55A-195
NOTE: Also check intermediate connector A-13, joint connec-
tor C-01, junction block connectors C-214 and C-215 for loose,
corroded, or damaged terminals, or terminals pushed back in
the connector. If intermediate connector A-13, joint connector
C-01, junction block connector C-214 or C-215 is damaged,
repair or replace the connector as described in GROUP 00E,
Harness Connector Inspection
.
Q: Is the wiring harness between A/C compressor clutch
relay connector B-18X (terminal 2) and the ignition
switch (IG2) in good condition?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Repair the wiring harness. Check that the air
conditioning works normally.
AC305210
A-13 (GR)
AR
CONNECTOR: A-13
AC305231
CONNECTOR: C-01
BO
AC305416
CONNECTORS: C-214, C-215
JUNCTION BLOCK
(FRONT VIEW)
C-215
HARNESS SIDE
C-214
C-214
HARNESS SIDE
C-215
10
1
6
14
5
12
13
4
11
7
2
3
8
9
AL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст