Mitsubishi Galant 9G. Manual — part 1036
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-444
Judgment Criteria
• Long-term fuel trim has continued to be lower
than
−12.5 percent for 5 seconds.
or
• Short-term fuel trim has continued to be lower
than
−12.5 percent for 5 seconds.
Check Conditions
• Engine coolant temperature is higher than 76°C
(169
°F).
• Under the closed loop air/fuel ratio control.
Judgment Criteria
• Long-term fuel trim has continued to be −12.5
percent for 2 seconds.
or
• Short-term fuel trim has continued to be −30.0
percent for 2 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 2
− Fuel Trim Monitor
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Mass airflow sensor failed.
• Injector (Number 2, 4, 6) failed.
• Incorrect fuel pressure.
• Engine coolant temperature sensor failed.
• Intake air temperature sensor failed.
• Barometric pressure sensor failed.
• Manifold absolute pressure sensor failed.
• Harness damage in left bank injector circuit or
connector damage.
• PCM failed.
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, check data list item 12:
Mass Airflow Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
12, Mass Airflow Sensor.
(4) Warm up the engine to normal operating temperature: 80
°C
to 95
°C (176°F to 203°F).
• When idling, between 2.0 and 6.0 g/sec.
• When 2,500 r/min, between 8.0 and 16.0 g/sec.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : YES: Go to Step 2.
NO : Refer to, DTC P0101
− Mass Airflow Circuit
Range/Performance Problem
, DTC P0102
− Mass Airflow Circuit Low Input
, DTC
P0103
− Mass Airflow Circuit High Input
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-445
STEP 2. Using scan tool MB991958, check data list item 13:
Intake Air Temperature Sensor.
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item
13, Intake Air Temperature Sensor.
• The intake air temperature and temperature shown with
the scan tool should approximately match.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 3.
NO : Refer to DTC P0111
− Intake Air Temperature Circuit
Range/Performance Problem
DTC P0112
− Intake Air Temperature Circuit Low Input
, DTC P0113
− Intake Air Temperature
.
STEP 3. Using scan tool MB991958, check data list item 21:
Engine Coolant Temperature Sensor.
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item
21, Engine Coolant Temperature Sensor.
• The engine coolant temperature and temperature
shown with the scan tool should approximately match.
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 4.
NO : Refer to DTC P0116
− Engine Coolant Temperature
Circuit Range/Performance Problem
, DTC
P0117
− Engine Coolant Temperature Circuit Low
, DTC P0118
− Engine Coolant
Temperature Circuit High Input
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-446
STEP 4. Using scan tool MB991958, check data list item 25:
Barometric Pressure Sensor.
(1) Turn the ignition switch to the "ON" position.
(2) Set scan tool MB991958 to the data reading mode for item
25, Barometric Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg).
• When altitude is 1,800 m (5,906 feet), 81 kPa. (23.9
in.Hg)
(3) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 5.
NO : Refer to DTC P2228
− Barometric Pressure Circuit
Low Input
, DTC P2229
− Barometric
Pressure Circuit High Input
STEP 5. Using scan tool MB991958, check data list item 95:
Manifold Absolute Pressure Sensor.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
95, Manifold Absolute Pressure Sensor.
• When altitude is 0 m (0 foot), 101 kPa (29.8 in.Hg).
• When altitude is 600 m (1,969 feet), 95 kPa (28.1 in.Hg).
• When altitude is 1,200 m (3,937 feet), 88 kPa (26.0
in.Hg).
• When altitude is 1,800 m (5,906 feet), 81 kPa (23.9
in.Hg).
(4) Start the engine.
• When the engine is idling, 16 − 36 kPa (4.7 − 10.6
in.Hg).
• When the engine is suddenly revved, manifold absolute
pressure varies.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : Go to Step 6.
NO : Refer to DTC P0106
− Manifold Absolute Pressure
Circuit Range / Performance Problem
, DTC
P0107
− Manifold Absolute Pressure Circuit Low
Input
, DTC P0108
−Manifold Absolute
Pressure Circuit High Input
.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-447
STEP 6. Check the left bank injector.
(1) Disconnect the left bank injector connector B-30, B-27 ,
B-26.
(2) Measure the resistance between each injector side
connector terminal No. 1 and No. 2.
Standard value: 10.5
− 13.5 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 10.5 and 13.5 ohms
[at 20
°C (68°F)]?
YES : Go to Step 7.
NO : Replace the injector. Then go to Step 9.
STEP 7. Check the fuel pressure.
Refer to On-vehicle Service
− Fuel Pressure Test
Q: Is the fuel pressure normal?
YES : Go to Step 8.
NO : Repair it. Then go to Step 9.
AK303075
M
1
2
CONNECTOR: B-26, B-27, B-30
B-30 (GR)
B-27 (GR)
B-26 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AB
AK000559
2
1
INJECTOR SIDE
CONNECTOR
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст