Mitsubishi Galant 9G. Manual — part 1356
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-528
(4) Measure the resistance between joint connector (3)
terminal 15 and combination meter connector terminal 15.
OK: 2 ohms or less
(5) Measure the resistance between joint connector (3)
terminal 4 and combination meter connector terminal 14.
OK: 2 ohms or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Do all the resistances measure 2 ohms or less?
YES : If all the resistances measure 2 ohms or less, power
supply to the combination meter may be suspected.
Diagnose the combination meter by referring to
GROUP 54A, Combination meter assembly
NO : If either of the resistances measures more than 2
ohms or all the resistances measure more than 2
ohms, repair the wiring harness between joint
connector (3) and the combination meter connector.
AC204582
HARNESS SIDE: C-02
BZ
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
G
G
22
11
5
16
19
20
21
17
18
8
10 9
7 6
13
1514
12
2
4 3
1
TEST
HARNESS
HARNESS SIDE: C-101
TEST
HARNESS
AC204582
HARNESS SIDE: C-02
TEST
HARNESS
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
G
G
22
11
5
16
19
20
21
17
18
8
10 9
7 6
13
1514
12
2
4 3
1
TEST
HARNESS
HARNESS SIDE: C-101
CA
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-529
STEP 8. Check ETACS-ECU connector C-218 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CAUTION
The strand end of the twisted wire should be within 10 cm
(4 inches) from the connector. For details refer to
Q: Is ETACS-ECU connector C-218 in good condition?
YES : Go to Step 9.
NO : Repair the damaged parts.
STEP 9. Using scan tool MB991958, diagnose the CAN bus
line (Disconnect ETACS-ECU connector C-218, and check
the ETACS-ECU system).
(1) Disconnect ETACS-ECU connector C-218.
(2) Turn the ignition switch to the "ON" position.
(3) Diagnose CAN bus lines, and check if the MUT-III screen is
as shown in the illustration.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
(5) Connect ETACS-ECU connector C-218.
Q: Does the MUT-III screen correspond to the illustration?
YES : If the MUT-III screen corresponds to the illustration,
go to Step 10 .
NO : If the MUT-III screen does not correspond to the
illustration, go to Step 11.
AC305413
C-218 (GR)
CONNECTOR: C-218
AI
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
68
74
63
66
72
73
67
65 64
61
70
71
62
69
60
57
58
59
56 55
52
54 53
51
AC305413
C-218 (GR)
CONNECTOR: C-218
AI
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
68
74
63
66
72
73
67
65 64
61
70
71
62
69
60
57
58
59
56 55
52
54 53
51
AC306075
: Red section on screen
AD
ETACS
-ECU
AC-ECU
SRS-ECU
C.DISPLAY
MUT
J/C
METER
-ECU
PCM
ABS-ECU
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-530
STEP 10. Check the CAN bus lines between joint
connector (3) and the ETACS-ECU. Measure the resistance
between joint connector (3) C-02 and ETACS-ECU
connector C-218.
CAUTION
A digital multimeter should be used. For details refer to
.
CAUTION
The test wiring harness should be used. For details refer to
.
(1) Disconnect joint connector (3) C-02 and ETACS-ECU
connector C-218, and measure the resistances at the wiring
harness sides of joint connector (3) C-02 and ETACS-ECU
connector C-218.
(2) Turn the ignition switch to the "LOCK" (OFF) position.
CAUTION
Disconnect the negative battery terminal. For details refer
to
(3) Disconnect the negative battery terminal.
AC305231AP
CONNECTOR: C-02
AC305413
C-218 (GR)
CONNECTOR: C-218
AI
HARNESS SIDE
JUNCTION BLOCK
(REAR VIEW)
68
74
63
66
72
73
67
65 64
61
70
71
62
69
60
57
58
59
56 55
52
54 53
51
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-531
(4) Measure the resistance between joint connector (3)
terminal 16 and ETACS-ECU connector terminal 73.
OK: 2 ohms or less
(5) Measure the resistance between joint connector (3)
terminal 5 and ETACS-ECU connector terminal 72.
OK: 2 ohms or less
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
Q: Do all the resistances measure 2 ohms or less?
YES : If all the resistances measure 2 ohms or less, power
supply to the ETACS-ECU may be suspected.
Diagnose the ETACS-ECU by referring to GROUP
54B, Diagnosis
.
NO : If either of the resistances measures more than 2
ohms or all the resistances measure more than 2
ohms, repair the wiring harness between joint
connector (3) and the ETACS-ECU connector.
AC204582
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
51
53
54
52
55
56
595857
60
69
62
71 70
61
64
65
67
7372
66
63
74
68
TEST
HARNESS
CL
HARNESS SIDE: C-02
HARNESS SIDE: C-218
TEST
HARNESS
AC204582
11
22
10
21
9
20
8
19
7
18
6
17
5
16
4
15
3
14
2
13
1
12
51
53
54
52
55
56
595857
60
69
62
71 70
61
64
65
67
7372
66
63
74
68
TEST
HARNESS
CN
TEST
HARNESS
HARNESS SIDE: C-02
HARNESS SIDE: C-218
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст