Mitsubishi Galant 9G. Manual — part 961
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-144
DTC P0117: Engine Coolant Temperature Circuit Low Input
CAUTION
If DTC P0117 has been set, TCL and air condi-
tioner related DTC U1120 is also set. After P0117
has been diagnosed, don't forget to erase DTC
U1120.
YELLO
W
-GREEN
BLA
CK
AK302836
ENGINE COOLANT
TEMPERATURE SENSOR
POWERTRAIN CONTROL MODULE(PCM)
5 V
93
2
B-104
(MU802406)
69
1
Engine Coolant Temperature Sensor Circuit
1 2
B-21
B-22
52
51
53 54 55 56
57
58 59 60 61 62
63
64 65 66 67 68 69
70
71 72 73 74 75
76
77 78 79 80 81 82
83
100
99
92
91
93 94 95
96 97 98
101 102 103 104
105 106 107 108
109 110 111 112 113
AK303036
CONNECTOR: B-104
AB
B-104 (B)
ENGINE
COOLANT
TEMPERATURE
SENSOR
THROTTLE
BODY
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-145
.
CIRCUIT OPERATION
• 5-volt voltage is applied to the engine coolant
temperature sensor output terminal (terminal No.
1) from the PCM (terminal No. 93) via the resistor
in the PCM. The ground terminal (terminal No. 2)
is grounded with PCM (terminal No. 69).
• The engine coolant temperature sensor is a neg-
ative temperature coefficient type of resistor. It
has the characteristic that when the engine cool-
ant temperature rises the resistance decreases.
• The engine coolant temperature sensor output
voltage increases when the resistance increases
and decreases when the resistance decreases.
.
TECHNICAL DESCRIPTION
• The engine coolant temperature sensor converts
the engine coolant temperature to a voltage and
outputs it.
• The PCM checks whether this voltage is within a
specified range.
.
DESCRIPTIONS OF MONITOR METHODS
Engine coolant temperature sensor output voltage is
out of specified range.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS
(Other monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• Not applicable
Sensor (The sensor below is determined to be
normal)
• Not applicable
.
AK303013
CONNECTORS: B-21, B-22
PCM
AB
AIR CLEANER
B-22 (B)
B-21 (B)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-146
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 2 seconds or more have passed since the engine
starting sequence was completed.
Judgement Criteria
• Engine coolant temperature sensor output volt-
age has continued to be 0.1 volt or lower [corre-
sponding to coolant temperature of 140
°C
(284
°F) or higher] for 2 seconds.
.
OBD-II DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-II Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most
likely causes for this code to be set are:)
• Engine coolant temperature sensor failed.
• Shorted engine coolant temperature sensor cir-
cuit, or connector damage.
• PCM failed.
START
OUTPUT VOLTAGE > 4.6V
OUTPUT VOLTAGE < 0.1V
END
NO
NO
NO
YES
YES
YES
MALFUNCTION
GOOD
CONTINUOUS
FAILURE FOR 2secs
MONITORING
CONDITIONS?
NO
YES
AK302388
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-147
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Using scan tool MB991958, check data list item 21:
Engine Coolant Temperature Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to the data reading mode for item
21, Engine Coolant Temperature Sensor.
• The engine coolant temperature and temperature
shown with the scan tool should approximately match.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
NO : Go to Step 2.
STEP 2. Check harness connector B-104 at the engine
coolant temperature sensor for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. Then go to Step 6.
AC305412
AB
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
1
2
AK303037
HARNESS
CONNECTOR:
COMPONENT SIDE
CONNECTOR: B-104
AB
B-104 (B)
THROTTLE
BODY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст