Mitsubishi Galant 9G. Manual — part 388
DOOR
TSB Revision
BODY
42-32
GLASS SLIDING MECHANISM CHECK AND
ADJUSTMENT
M1429000900109
If the window glass automatically starts moving downwards at
the wrong time while it is being raised, carry out the following
adjustment or replacement procedures.
1. Remove the door trim assembly (Refer to GROUP 52A,
2. Remove the waterproof film (Refer to
CAUTION
Insert a cushion or similar object to prevent damage to the
glass if it should fall.
3. Remove the window regulator assembly from the door
window glass, and then raise and lower the door window
glass by hand to check the operation force.
4. If the door window glass does not move up and down
smoothly, check or repair the following points:
• Check the installation condition of the runchannel.
• Repair any twisting in the door sash.
• Check the installation condition of the lower sash.
NOTE: To align the lower sash, loosen the lower sash
mounting bolts, and move the lower sash along the oblong
mounting holes.
5. If repair or adjustment is not possible, replace the door
assembly.
POWER WINDOW TIMER FUNCTION CHECK
M1429004300154
After the doors are closed and the ignition switch is turned to
the "LOCK" (OFF) position, the power windows should work
within 30 seconds. The timer expires if the front door is opened
during that 30 seconds. If it does not, carry out the timer trou-
bleshooting in GROUP 54B, SWS Diagnosis
AC306502
AC306503
AC307036
<FRONT DOOR>
<REAR DOOR>
RUNCHANNEL
DOOR
SASH
LOWER SASH
RUNCHANNEL
DOOR
SASH
LOWER
SASH
AB
DOOR
TSB Revision
BODY
42-33
POWER WINDOW OPERATING CURRENT CHECK
M1429001100195
1. Remove the power window fuse and connect an ammeter
as shown in the illustration.
2. When the power window switch is pressed in the “UP”
position, a large amount of current flows from the time the
window starts to close until it is fully closed, Measure the
current during this time
Standard value (A): 5
± 1A [Power supply voltage
14.5
± 0.5V, 25°C (77°F)]
3. If the operation current is outside the standard value, refer to
POWER WINDOW RELAY CHECK
M1429001800213
AC305015 AG
BATTERY
VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
4
− 5
Open circuit
• Connect terminal
No. 3 and the
negative battery
terminal.
• Connect terminal
No. 1 and the
positive battery
terminal.
4
− 5
Less than 2 ohms
AC305030
AC306501
1
3
4
5
1 2
4
5
3
POWER WINDOW RELAY
INSTRUMENT
PANEL
AB
DOOR
TSB Revision
BODY
42-34
CIRCUIT BREAKER (INCORPORATED IN THE
POWER WINDOW MOTOR) INSPECTION
M1429001000284
1. Pull the power window switch to the UP position to fully
close the door window glass, and keep pulling the switch for
an additional ten seconds.
2. Release the power window switch from the UP position and
immediately press it to the DOWN position. The condition of
the circuit breaker is good if the door window glass starts to
move downwards within about 60 seconds.
POWER WINDOW CHECK
M1429004400214
1. Operate the power window switch of each door to verify that
the power windows operate properly. If they don't, then
troubleshoot as described in GROUP 54B, SWS Diagnosis
2. Turn ON the power window lock switch of the power window
main switch. Then operate the passenger's door and rear
door power window sub-switches to ensure that they do not
operate. If they do, replace the power window main switch
(Refer to
CENTRAL DOOR LOCKING SYSTEM
INSPECTION
M1427001100144
Check the following. Troubleshoot if operations malfunction
(Refer to GROUP 54B, SWS Diagnosis
).
• Insert the key into the driver's key cylinder and turn once to
the unlock side to unlock the driver's door. Turn the key
once again to the unlock side to unlock all doors.
• All doors can be locked using the door lock switch built into
the front power window (main or sub <RH>) switch.
DOOR
TSB Revision
BODY
42-35
DOOR OUTSIDE HANDLE PLAY CHECK
M1423001600288
1. Check that the door outside handle play is within the
standard value range.
Standard value (B):
Front door: 10
± 3.5 mm (0.39 ± 0.138 inch)
Rear door: 11.2
± 4 mm (0.441 ± 0.16 inch)
2. If the door outside handle play is not within the standard
value range, check the door outside handle or the door latch
assembly. Replace if necessary.
DOOR INSIDE HANDLE PLAY CHECK
M1423009400028
DOOR INSIDE HANDLE KNOB PLAY CHECK
1. Check that the door inside handle play is within the standard
value range.
Standard value (B):
Front door: 26.1
−58.1 mm (1.028 −2.287 inches) [Tar-
get value 41 mm (1.61inches)]
Rear door: 30.3
−58.1 mm (1.193 −2.287 inches) [Target
value 41 mm (1.61inches)]
2. If the door inside handle play is not within the standard value
range, check the door inside handle or the inside handle
cable. Replace if necessary.
AC306509
AC205105
AC307031
SECTION A – A
A
A
B
AB
AC306508
AC205104
AC307029
A
A
B
AB
SECTION A – A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст