Mitsubishi L200. Manual — part 580
FRONT SEAT ASSEMBLY
INTERIOR
52A-26
<BENCH SEAT>
AC509460AC
5
11
4
3
10
9
N
N
7
1
6
2
8
Disassembly steps
1.
Front seat cushion assembly
2.
Hog ling
3.
Front seat cushion cover
4.
Front seat cushion pad
5.
Inner seat cushion frame
6.
Front seatback assembly
<<
A
>>
7.
Headrestraint guide
8.
Front seatback cover
9.
Hog ling
10. Front seatback pad
11. Front seatback frame
DISASSEMBLY SERVICE POINT
<<A>> HEADRESTRAINT GUIDE REMOVAL
AC205342
Remove the headrest guides while pushing the on
both sides inward.
INSPECTION
M1522001400608
POWER SEAT SWITCH CONTINUITY
CHECK
AC507447AB
Connect the (+) terminal of the battery to the power
seat connector terminal No.2 and the (
−) terminal to
terminal No.1, and check that the power seat works
normally.
FRONT SEAT ASSEMBLY
INTERIOR
52A-27
HEATED SEAT RELAY CONTINUITY
CHECK
AC510001
4
3
2
1
AB
Seat heater relay
Junction block
Battery voltage Tester
connection
Specified
condition
Not applied
3
− 4
Open circuit
• Connect
terminal 2 to
the positive
battery
terminal
• Connect
terminal 1 to
the negative
battery
terminal
Continuity (Less
than 2
Ω)
HEATED SEAT SWITCH CONTINUITY
CHECK
5
2
4
1
6
3
AC501130
Inspect the heated seat switch for continuity.
Switch
position
Tester
connection
Specified
condition
Note
HI
1
− 2
Continuity
(Less than
2
Ω)
2(+)
− 6(−)
Indicator
3
− 4
Illumination
OFF
3
− 4
Illumination
LOW
2
− 5
2(+)
− 6(−)
Indicator
3
− 4
Illumination
SEAT CUSHION HEATER CHECK
AC509808
Connector 2
Connector 2-1
AB
Measure the resistance between the terminals.
Standard value (At room temperature 20
°C):
Connector, terminal No.
Specified condition
Connector 2, terminal 3
−
Connector 2
− 1, terminal 1
3.79
− 4.53 Ω
Connector 2, terminal 1
−
Connector 2
− 1, terminal 1
3.98
− 4.76 Ω
Connector 2, terminal 3
−
Connector 2, terminal 1
0.22
− 0.26 Ω
SEATBACK HEATER CHECK
AC509810AB
Measure the resistance between the terminals.
Standard value (At room temperature 20
°C):
Tester connection
Specified condition
1
− 2
5.01
− 6.00 Ω
REAR SEAT ASSEMBLY <CLUB CAB, DOUBLE CAB>
INTERIOR
52A-28
REAR SEAT ASSEMBLY <CLUB CAB, DOUBLE CAB>
REMOVAL AND INSTALLATION
M1522001801007
<CLUB CAB>
ACA01331
1
2
1
2
5
2
2
3
1
4
22 ± 4 N·m
22 ± 4 N·m
22 ± 4 N·m
22 ± 4 N·m
AC
22 ± 4 N·m
Removal steps
1.
Rear seat hinge cover outer
2.
Rear seat hinge cover inner
3.
Rear seat cushion assembly
4.
Rear seatback assembly
>>
A
5.
Headrestraint
Removal steps (Continued)
REAR SEAT ASSEMBLY <CLUB CAB, DOUBLE CAB>
INTERIOR
52A-29
<DOUBLE CAB>
AC509494AB
1
1
3
2
44 ± 10 N·m
30 ± 5 N·m
20 ± 4 N·m
30 ± 5 N·m
1
1.
Headrestraint
Removal steps
2.
Rear seat back assembly
3.
Rear seat cushion assembly
INSTALLATION SERVICE POINT
ACA01403
1
2
2
AB
>>A<< HEADRESTRAINT INSTALLATION (CLUB
CAB)
Tighten the bolts in the order shown in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст