Mitsubishi L200. Manual — part 223
GLOW SYSTEM
ENGINE ELECTRICAL
16-22
ON-VEHICLE SERVICE
GLOW PLUG CHECK <EURO5>
M1164003400305
AK403892 AC
( - )
( + )
1. Disconnect the glow plug connector.
2. Measure the resistance between the glow plug
terminal and the body, or the glow plug terminal
and the cylinder head.
Standard value: 0.6
− 1.4 Ω (at 20°C)
SELF-REGULATING GLOW SYSTEM CHECK <EXCEPT EURO5>
M1164001000260
SELF-REGULATING GLOW SYSTEM CHECK
1. Check that the battery voltage is 11
− 13 V.
2. Check that the engine coolant temperature is
40
°C or less.
NOTE: If the engine coolant temperature is too
high, disconnect the engine coolant temperature
sensor connector.
AK403875 AC
( - )
( + )
3. Measure the resistance between the glow plug
plate and the glow plug body (earth).
Standard value: 0.15
− 0.25 Ω (at 20°C)
NOTE: The resistance value is the parallel resist-
ance value for the four glow plugs.
4. Connect a voltmeter between the glow plug plate
and the glow plug body (earth).
5. Measure the voltage immediately after the ignition
switch is turned to ON (without starting the
engine).
Standard value: 9
− 11 V (Drops to 0 V after 4
− 8 seconds have passed)
In addition, check to be sure that the glow indicator
lamp (red) illuminates immediately after the ignition
switch is turned to ON.
NOTE: The time during which the voltage appears
(energizing time) will depend on the engine cool-
ant temperature.
6. Measure the voltage while the engine is cranking.
Standard value: 6 V or more
7. Start the engine and measure the voltage while
the engine is warming up.
However, if the engine coolant temperature rises
above 60
°C or when 180 seconds have passed
since the engine was started, the voltage will
always return to 0 V (Refer to the Glow Plug
Energization Timing Chart).
Standard value: 12
− 15 V
GLOW SYSTEM
ENGINE ELECTRICAL
16-23
Glow Plug Energization Timing Chart <Reference>
AK403877
T1: Glow lamp
T2: Glow plug relay drive time after ignition switch is turned ON
T3: Glow plug relay drive time after engine starts (after glow)
START
Ignition
switch
Glow
lamp
Glow plug
relay
Crank angle
sensor
NOTE
After glow time T3 becomes longer as the engine coolant temperature drops
ON
OFF
ON
OFF
Idle
0 r/min
ON
OFF
AG
T1
T2
T3
CHECK AT THE ECU TERMINALS <EURO5>
M1164003600246
Refer to GROUP 13A
− Troubleshooting − Check at
the engine-ECU terminals .
CHECK AT THE ECU TERMINALS <EXCEPT EURO5>
M1164003600257
Refer to GROUP 13A
− Troubleshooting − Check at
the engine-ECU terminals.
GLOW PLUG RELAY CHECK <EXCEPT EURO5>
M1164003300160
AK403878AB
Glow plug relay
1. Disconnect the glow plug relay connector.
2. Measure resistance between terminal C and
terminal E.
Standard value: 18
− 22 Ω (at 20°C)
3. Use jumper cables to connect terminal C of the
glow plug relay to the battery (+) terminal and
terminal E to the battery (
−) terminal.
GLOW SYSTEM
ENGINE ELECTRICAL
16-24
CAUTION
1. Always be sure to disconnect the harnesses
connected to glow plug relay terminals B and
G before using the jumper cable.
2. The terminals of the disconnected harnesses
must not be shorted to earth.
3. When connecting the jumper cable, be very
careful not to make a mistake in connecting
the terminal, as this will cause damage to the
relay.
AK403881
B
C E
G
C
E
AB
G terminal
B terminal
4. Check the continuity between glow plug relay
terminals B and G while disconnecting and
connecting the jumper cable at the battery (+)
terminal.
Jumper cable at battery (+)
terminal
Continuity between
terminals B
− G
Connected
Continuity (0.01
Ω or less)
Disconnected
No continuity (infinite
resistance)
GLOW PLUG CHECK <EXCEPT EURO5>
M1164003400316
AK403892 AC
( - )
( + )
1. Remove the glow plug plate.
2. Measure the resistance between the glow plug
terminals and the body.
Standard value: 0.6
− 1.0 Ω (at 20°C)
ENGINE COOLANT TEMPERATURE
SENSOR CHECK <EXCEPT EURO5>
M1164003500067
Refer to GROUP 13A
− On-vehicle service − Engine
coolant temperature sensor check.
GLOW SYSTEM
ENGINE ELECTRICAL
16-25
GLOW PLUG
REMOVAL AND INSTALLATION
M1164001800512
Pre-removal Operation
• Throttle Body Assembly Removal (Refer to GROUP 13A
− Throttle Body ).
• EGR Valve and EGR Valve Pipe Removal (Refer to
GROUP 17
− EGR Valve and EGR Cooler ).
Post-installation Operation
• EGR Valve and EGR Valve Pipe Installation (Refer to
GROUP 17
− EGR Valve and EGR Cooler ).
• Throttle Body Assembly Installation (Refer to GROUP
13A
− Throttle Body ).
AC503049AE
5.0 ± 1.0 N·m
1.8 ± 0.2 N·m
17 ± 2 N·m
1
2
Removal steps
1.
Glow plug connecting plate
<Except Euro5>
2.
Glow plug
GLOW PLUG RELAY <Except Euro5>
REMOVAL AND INSTALLATION
M1164002400023
AC807146
1
2
3
9.0 ± 1.0 N·m
5.0 ± 1.0 N·m
9.0 ± 1.0 N·m
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст