Mitsubishi L200. Manual — part 330
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V4A5>
23C-29
CAUTION
Carefully hammer the special tool so that the oil
pan mounting surface is not damaged.
AK403345AB
MD998727
6. Remove the twenty oil pan mounting bolts and
then use the special tool Oil pan remover
(MD998727) to remove the oil pan.
AK403346
O-ring
Oil filter
AB
7. Remove the oil filter and O-ring.
AK403347
8. Remove the detent spring.
AK700990
AB
9. Disconnect the valve body harness connectors.
AK701362AB
Oil temperature sensor
AK403349AB
O-ring
10.Remove the twenty valve body mounting bolts
and then remove the valve body, O-ring and oil
temperature sensor.
NOTE:
.
•
The twenty valve body mounting bolts are
plated bolts.
•
The O-ring is mounted on the transmission
case side as shown in the illustration. How-
ever there may be cases when it will come off
with the valve body.
AK403350AB
Snap ring
11.Remove the snap ring and disconnect the
solenoid valve harness.
AK403351AB
Oil seals
Oil strainer
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V4A5>
23C-30
12.Remove the oil strainer and two oil seals.
AK403352AB
1
2
3
4
13.Remover each accumulator piston, seal ring and
spring.
No.
Name
1
For overdrive clutch
2
For second brake
3
For low/reverse brake
4
For underdrive clutch
NOTE: To make assembly easier, attach an iden-
tification tag on the removed accumulator piston.
AK403378AB
Spring pin
14.Remove the detent lever spring pin.
AK403353AB
Pin
Detent lever
Parking roller
rod
Manual control
shaft
15.Remove the pin, and then remove the manual
control shaft, two O-rings, detent lever and
parking roller rod.
AK503505AB
16.Remove the eight converter housing mounting
bolts, and then the converter housing.
AK403355
AB
17.Remove the ten oil pump mounting bolts.
18.Install special tool Oil pump remover (MD998333)
into the bolt hole shown in the illustration.
AK403356AB
MD998333
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V4A5>
23C-31
19.While screwing in special tools Oil pump remover
(MD998333) evenly, remove the oil pump.
20.Remove the oil pump gasket.
AK403357AD
Trust race No.1
Trust bearing No.2
21.Remove the thrust race No.1 and thrust bearing
No.2.
NOTE: The thrust race No.1 may be attached to
the oil pump.
AK403358
22.Remove the reverse overdrive clutch.
AK403359AD
Overdrive
clutch hub
Thrust bearing No.3
23.Remove the overdrive clutch hub and thrust
bearing No.3.
AK403360AD
Thrust bearing No.4
24.Remove the thrust bearing No.4.
NOTE: The thrust bearing No.4 may be attached
to the overdrive clutch hub.
AK403361
25.Remove the reverse sun gear.
AK403362
26.Remove the snap ring.
AK403363AB
Second brake
Return spring
27.Remove the second brake and return spring.
AK403364
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL <V4A5>
23C-32
28.Remove the low/reverse annulus gear.
AK403365
29.Remove the pressure plate, brake plates and
brake discs.
AK403366AD
Thrust bearing No.7
30.Remove the thrust bearing No.7.
NOTE: The thrust bearing No.7 may be attached
to the low/reverse annulus gear.
AK403367
31.Remove the snap ring.
AK403368AB
Reaction plate
Brake disc
32.Remove the reaction plate and one brake disc.
AK403369
33.Remove the snap ring.
AK403370
34.Remove the brake plates, brake discs, and
pressure plate.
AK403371
35.Remove the wave spring.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст