Mitsubishi L200. Manual — part 731
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-291
STEP 3. Check the wiring harness between radio
and CD player connector C-125 (terminal 11) and
fusible link 20 (battery).
• Check the power supply line for open circuit and
short circuit.
NOTE:
Prior to the wiring harness inspection, check junction
block connectors C-209, C-213 and joint connector
C-132, and repair if necessary.
Q: Are the wiring harness between radio and CD
player connector C-125 (terminal 11) and fusible
link 20 (battery) in good condition?
YES :
Repair or replace the radio and CD player.
Check that a memory is retained.
NO :
Repair or replace the damage
component(s). Check that a memory is
retained.
AC903856AE
Harness side
Connector: C-125 <LHD>
AC903868
AE
Harness side
Connector: C-125 <RHD>
AC903853
Connector: C-132 <LHD>
AC
C-132 (GR)
AC903865
Connector: C-132 <RHD>
AB
C-132 (GR)
AC509934
Connectors: C-209, C-213 <LHD>
Junction block (Front view)
C-213
C-209
C-213
C-209
AC
Harness side
Harness side
AC509936
Connectors: C-209, C-213 <RHD>
C-213
C-209
AC
Junction block
(Front view)
C-213
C-209
Harness side Harness side
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-292
Inspection Procedure 16: CD can not be inserted.
DIAGNOSIS PROCEDURE
STEP 1. Check that a CD has been already
loaded.
Q: Has a CD been already loaded?
NO :
Go to Step 2.
YES :
Take out the CD (If the CD can not be
ejected, refer to INSPECTION
PROCEDURE 20
CD can be inserted.
STEP 2. Check how a CD is inserted.
• Ensure that the ignition switch is at "ACC" or
"ON".
NOTE: If you try to load a CD when the ignition
switch is at the positions other than "ACC" or "ON",
the CD will not be inserted completely and then
rejected.
Q: If you try to load the CD, does the CD stops halfway
and then rejected?
YES :
Refer to INSPECTION PROCEDURE 20
.
NO :
Go to Step 3.
STEP 3. Check after the CD is loaded.
NOTE: Even though the CD is loaded, "E" (error) is
sometimes displayed with the CD rejected because
of vibration/shock or dew on the CD face or optical
lens.
Q: Though the CD is inserted completely, is "E" (error)
displayed and the CD ejected?
YES :
Go to Step 4.
NO :
The procedure is complete.
STEP 4. Check the CD.
Check the CD for the conditions below:
• Is the CD loaded with its label facing down?
• Is the recorded face dirty or scratched?
• Is there dew on the recorded face?
Q: Is the CD in good condition?
YES :
Go to Step 5.
NO :
The original CD is defective. Check that a
CD can be inserted.
STEP 5. Check again using a normal CD, which is
not dirty or scratched.
• Load another normal CD.
• Check that the CD player recognizes and play the
CD.
Q: When you substitute another normal CD, is the CD
loaded correctly?
YES :
The original CD is defective. Check that a
CD can be inserted.
NO :
Replace the radio with CD player. The
procedure is complete.
Inspection Procedure 17: No sound. (CD only)
DIAGNOSIS PROCEDURE
STEP 1. Check again using a normal CD, which is
not dirty or scratched.
Q: When you substitute another normal CD, is the CD
played normally?
YES :
The original CD is defective. The CD player
should sound normally.
NO :
Go to Step 2.
STEP 2. Check power supply to the CD player
when the ignition switch is at "ACC" or "ACC".
Q: Is the radio and CD player energized when the
ignition switch is turned to the "ACC" or "ON"
position?
YES :
Replace the radio and CD player. The
procedure is complete.
NO :
Check the memory backup power supply
circuit. Refer to Inspection Procedure 1
.
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-293
Inspection Procedure 18: CD sound skips.
DIAGNOSIS PROCEDURE
STEP 1. Check the state in which the sound on
the CD jumps.
Q: Does the sound jump when the car is parked?
YES :
Go to Step 2.
NO :
Go to Step 4.
STEP 2. Check the surface of the CD.
Q: Are there any scratches or soiling on the CD?
YES :
The CD is defective if there are any
scratches. Clean the CD surface if it is dirty.
Check that a CD sound skip is resolved.
NO :
Go to Step 3.
STEP 3. Check when replacing with a CD that can
be played normally without any scratches or
soiling.
Q: Does the CD play normally when replaced with a
CD that is not scratched or dirty and can play
normally?
YES :
Defective CD used. Check that a CD sound
skip is resolved.
NO :
Go to Step 4.
STEP 4. Check by tapping the radio and CD
player.
NOTE: Check by using a proper CD which is free
from scratches, dirt or any other abnormality.
Q: Does the sound jump when tapping the radio and
CD player?
YES :
Securely mount the radio and CD player.
Check that a CD sound skip is resolved.
NO :
Either repair or replace the radio and CD
player. (Take the following measures if a
servicing shop is closely).
1. Investigate in detail the state when
the sound jumps while driving the
car.
2. Describe the state to the service
shop for consultation.
3. Either repair or replace the radio and
CD player according to the
instructions of the service shop.
Check that a CD sound skip is resolved.
Inspection Procedure 19: Sound quality is poor.
DIAGNOSIS PROCEDURE
Check to see that the CD can be played normally
and that it is free of any scratches or soiling.
Replace with better sound quality CD.
Q: Is the sound quality better replacing the CD with a
clean CD without any scratches that can be
played?
YES :
Defective CD used. The sound quality
should return to normal.
NO :
Either repair or replace the radio and CD
player. The sound quality should return to
normal.
Inspection Procedure 20: CD can not be ejected.
DIAGNOSIS PROCEDURE
Check the power of ignition switch "ACC".
Q: Does the radio and CD player power turn ON when
the ignition switch is in the "ACC" or "ON"
position?
YES :
Replace the radio and CD player. Check
that a CD can be ejected normally.
NO :
Check the power supply circuit. Refer to
Inspection Procedure 1
RADIO AND CD PLAYER
CHASSIS ELECTRICAL
54A-294
ON-VEHICLE SERVICE
SPEAKER TEST
M1544005400932
RADIO AND CD PLAYER SPEAKER TEST
Enter the speaker test mode according to the follow-
ing steps:
1. Turn the Ignition switch to the "ACC" or "ON"
position and switch off the radio and CD player.
2. Press the following buttons in that order within
sixty seconds from step (1).
(1) Memory select "1" button
(2) "TUNE/SEEK (DOWN)" button
(3) "TUNE/SEEK (UP)" button
(4) Memory select "6" button
3. Check that the speaker, which is displayed on the
RV meter, sounds (If the [CH6] button is pressed,
the speaker will be changed).
4. If a button other than the [CH6] button is pressed,
or the ignition switch is turned to "LOCK" (OFF)
position, you will exit from the speaker connection
check mode.
REMOVAL AND INSTALLATION
M1544011300417
<NOT USING SPECIAL TOOL>
ACB01999AB
TUNE/SEEK
(DOWN) button
Memory select
button (1)
Radio and CD player
TUNE/SEEK
(UP) button
Memory select
button (6)
Display
Sound speaker
FL
Front door speaker (LH) and front tweeter (LH)
FR
Front door speaker (RH) and front tweeter (RH)
RL
Rear door speaker (LH)
RR
Rear door speaker (RH)
AC508514
3
C
B
B
A
A
1
4
2
Section A – A
Claw
Centre upper
panel
Section B – B
Claw
Centre upper
panel
Section C – C
Clip
Instrument
panel
AB
3
1
1
1
NOTE
(1) : Clip positions
(2) : Claw positions
C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст