Mitsubishi L200. Manual — part 608
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-103
Code No.B1403: Driver's air bag module (squib) system (short-circuited to the power supply)
AC805793
Driver's Air Bag Module (Squib) Circuit
AIR BAG MODULE
(SQUIB)
(DRIVER'S SIDE)
CONNECTOR
LOCK SWITCH
CONNECTOR
LOCK SWITCH
CLOCK SPRING
SRS-ECU
CONNECTOR
LOCK SWITCH
NOTE
: CONNECTOR COUPLED: ON
CONNECTOR UNCOUPLED: OFF
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple
AB
OPERATION
• The SRS-ECU judges how severe a collision is
by detecting signals from the front impact sensors
and the front air bag analogue G-sensor. If the
impact is over a predetermined level, the SRS-
ECU sends an ignition signal. At this time, if the
front air bag safing G-sensor is on, the SRS air
bag will inflate.
• The ignition signal is input to the air bag module
via the clock spring to inflate the air bag.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set if the driver’s air bag squib
wire(s) are short-circuited to the power supply.
PROBABLE CAUSES
• Malfunction of the clock spring
• Damaged harness wires and connectors
• Short to the power supply in the driver's air bag
module (squib) harness
• Malfunction of the SRS-ECU
DIAGNOSIS PROCEDURE
STEP 1. Check the diagnosis code by connecting
a dummy resistor. (M.U.T.-III diagnosis code)
(1) Disconnect the negative battery terminal.
AC501669
A
C-303 Air bag
module connector
AB
(2) By sliding the A section (in the figure) of air bag
module connector C-303 in arrow direction,
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-104
disconnect the connector.
AC303006AF
C-303 Air bag
module
connector
MB991865
(Dummy
resistor : 3 )
MB991866
(Resistor harness)
(3) Connect special tool dummy resistor (MB991865)
to special tool resistor harness (MB991866).
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(4) Insert special tool (MB991866) into clock spring
side air bag module connector C-303 by
backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnosis code memory, and check the
diagnosis code.
Q: Is diagnosis code B1403 out put?
YES :
Go to Step 2.
NO :
Replace the driver’s air bag module (Refer
to
STEP 2. Check the diagnosis code by connecting
a dummy resistor. (M.U.T.-III diagnosis code)
(1) Disconnect the negative battery terminal.
AC903858AD
Connector: C-305 <LHD>
Harness side
connector
(front view)
C-305 (Y)
AC903869AD
Connector: C-305 <RHD>
Harness side
connector
(front view)
C-305 (Y)
C-305
(2) Disconnect the clock spring connector C-305.
AC303587AM
C-305 Clock spring
connector
MB991865
(Dummy resistor: 3 )
MB991866
(Resistor harness)
(Rear view)
(3) Connect special tool dummy resistor (MB991865)
to special tool resistor harness (MB991866).
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(4) Insert special tool (MB991866) into clock spring
harness side connector C-305 (terminal No.3 and
4) by backprobing.
(5) Connect the negative battery terminal.
(6) Erase the diagnosis code memory, and check the
diagnosis code.
Q: Is diagnosis code B1403 set?
YES :
Go to Step 3.
NO :
Replace the clock spring (Refer to
).
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-105
STEP 3. Voltage measurement at the SRS-ECU
connector C-154.
(1) Disconnect the negative battery terminal.
AC801404
AJ
Connector: C-154
C-154 (Y)
Harness side
connector
(rear view)
(2) Disconnect SRS-ECU connector C-154.
AC903858AD
Connector: C-305 <LHD>
Harness side
connector
(front view)
C-305 (Y)
AC903869AD
Connector: C-305 <RHD>
Harness side
connector
(front view)
C-305 (Y)
C-305
DANGER
To prevents the air bag from deploying unin-
tentionally, disconnect the clock spring con-
nector C-305 to short the squib circuit.
(3) Disconnect the clock spring connector C-305.
AC801565
Section
A - A
C-154 Harness side connectors
(front view)
Cable tie
Terminal
7 mm or more
AD
Short spring
A
A
CAUTION
Insert an insulator such as a cable tie to a depth
of 7 mm or more, otherwise the short spring will
not be released.
(4) Insert a cable tie [3 mm wide, 0.5 mm thick]
between terminals 27, 28 and the short spring to
release the short spring.
(5) Connect the negative battery terminal.
(6) Turn the ignition switch to the "ON" position.
AC800963AN
C-154 Harness side connector
(rear view)
CAUTION
Do not insert a test probe into the terminal from
its front side directly as the connector contact
pressure may be weakened.
(7) Voltage measurement between C-154 harness
side connector terminals 27, 28 and body earth.
OK: 1 V or less
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the harness wires between SRS-
ECU connector C-154 (terminal No.27 and
28) and clock spring connector C-305
(terminal No.3 and 4).
STEP 4. Check whether the diagnosis code is
reset.
Q: Is diagnosis code B1403 set?
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-106
YES :
).
NO :
An intermittent malfunction is suspected
(Refer to GROUP 00, How to Cope with
Intermittent Malfunction ).
Code No.B1404: Driver's air bag module (squib ignition drive circuit) system detected short circuit
Code No.B1405: Driver's air bag module (squib ignition drive circuit) system detected open circuit
Code No.B1414: Passenger’s (front) air bag module (squib ignition drive circuit) system detected
short circuit
Code No.B1415: Passenger’s (front) air bag module (squib ignition drive circuit) system detected
open circuit
Code No.B1424: Side-airbag module (RH) (squib ignition drive circuit) system detected short circuit
Code No.B1425: Side-airbag module (RH) (squib ignition drive circuit) system detected open circuit
Code No.B1434: Side-airbag module (LH) (squib ignition drive circuit) system detected short circuit
Code No.B1435: Side-airbag module (LH) (squib ignition drive circuit) system detected open circuit
Code No.B1444: Curtain air bag module (RH) (squib ignition drive circuit) system detected short
circuit
Code No.B1445: Curtain air bag module (RH) (squib ignition drive circuit) system detected open
circuit
Code No.B1454: Curtain air bag module (LH) (squib ignition drive circuit) system detected short
circuit
Code No.B1455: Curtain air bag module (LH) (squib ignition drive circuit) system detected open
circuit
Code No.B1466: Analogue G-sensor system in the SRS-ECU (front air bag)
Code No.B1467: Safing G-sensor open circuit (front air bag)
Code No.B1468: Safing G-sensor short circuit (front air bag)
Code No.B1469: Analogue G-sensor system in the SRS-ECU (side air bag)
Code No.B1478: SRS-ECU capacitor circuit voltage too high
Code No.B1479: SRS-ECU capacitor circuit voltage too low
Code No.B1496: SRS-ECU non-volatile memory (EEPROM)
Code No.B1497: SRS-ECU application specific integrated circuit (for frontal activation)
Code No.B1498: SRS-ECU ROM or RAM
Code No.B1499: Collision decision
Code No.B1550: SRS warning lamp drive circuit malfunction
Code No.B1557: SRS-ECU application specific integrated circuit
Code No.B1607: Seat belt pre-tensioner (driver's side) (squib ignition drive circuit) system detected
short circuit
Code No.B1608: Seat belt pre-tensioner (driver's side) (squib ignition drive circuit) system detected
open circuit
Code No.B1613: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system
detected short circuit
Code No.B1614: Seat belt pre-tensioner (passenger’s side) (squib ignition drive circuit) system
detected open circuit
DIAGNOSIS CODE SET CONDITIONS
These diagnosis code are set when a fault is
detected in the SRS-ECU. The most likely causes for
this code to be set are shown in the table below:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст