Mitsubishi L200. Manual — part 698
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-159
STEP 4. Check the wiring harness from A-52
front fog lamp (LH) connector terminal or A-53
front fog lamp (RH) connector terminal No.1 to
body earth.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
STEP 5. Connector check: Connector check: A-
13X front fog lamp relay connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
STEP 6. Check the wiring harness from A-52
front fog lamp (LH) connector or A-53 front fog
lamp (RH) connector terminal No.2 to A-13X front
fog lamp relay connector terminal No.3.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
STEP 7. Retest the system.
Check that the front fog lamps illuminate normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Replace the front fog lamp(s).
AC903898
AI
Connector: A-52
Harness side
A-52 (B)
AC903897
AI
Connector: A-53
Harness side
A-53 (B)
AC903878
AE
Connector: A-13X
Relay box side
AC903878
AE
Connector: A-13X
Relay box side
AC903898
AI
Connector: A-52
Harness side
A-52 (B)
AC903897
AI
Connector: A-53
Harness side
A-53 (B)
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-160
ON-VEHICLE SERVICE
FRONT FOG LAMP AIMING
M1540400300680
CAUTION
When marking the aiming adjustment, be sure to
mask those lamps which are not being adjusted.
1. Measure the centre of the front fog lamps, as
shown in the illustration.
2. Set the distance between the screen and the
centre of the front fog lamps as shown in the
illustration.
3. Inflate the tyres to the specified pressures and
there should be no other load in the vehicles other
than driver or substituted weight of approximately
75 kg placed in the driver’s position.
4. With the engine running at 2,000 r/min, aim the
front fog lamp.
5. Remove the fog lamp bezel. (Refer to
6. Insert a Phillips screwdriver into the service hole
and place it on the adjusting screw.
7. Adjust the cut off line (boundary between light and
dark) position to the standard value with the
adjusting screw.
Standard value:
(Vertical direction) 60 mm (1.15
°) below hori-
zontal (H)
NOTE: The horizontal direction is non-adjustable. If
the deviation of the light beam axis exceeds the
standard value, check to be sure that the mounting
location or some other point is not defective.
AC805341
AD
Front fog lamp centre
<Single cab and vehicles for Russia>
AC800995AC
Front fog lamp
centre
<Vehicles for Europe (except for single cab)>
AC804645
AB
Screen
3 m
Fog lamp centre
Vehicle centre line
AC805332
AD
Adjusting screw
<Single cab and vehicles for Russia>
Phillips screwdriver
(Vertical direction adjustment)
AC800993AC
Phillips screwdriver
(Vertical direction adjustment)
<Vehicles for Europe (except for single cab)>
Adjusting screw
AC312871AC
Distance of
vertical direction
V
H
Lamp centre
Cut off line
High intensity zone
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-161
REPLACEMENT OF REPLACEABLE BULB
M1540400400557
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. If the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
1. Remove the fog lamp bezel and the fog lamp
assembly. (Refer to
.)
2. Disconnect the connector and withdraw the bulb.
3. After replacing the bulb, securely connect the
connector, and install the fog lamp assembly and
the fog lamp bezel.
REMOVAL AND INSTALLATION
M1540400500372
<SINGLE CAB AND VEHICLES FOR RUSSIA>
AC800929AB
Fog lamp bulb
Post-installation operation
Check the beam direction of the front fog lamp (Refer to
Front Fog Lamp Aiming
AC805351AB
1
2
3
4
0.7 ± 0.0 N·m
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-162
<VEHICLES FOR EUROPE (EXCEPT FOR SINGLE CAB)>
AC805699
1
Front
bumper
face
AB
Section A - A
Section B - B
Section C - C
Section D - D
Claw
A
A
Claw
Claw
Claw
1
1
1
Front
bumper
face
Front
bumper
face
Front
bumper
face
A
A
A
A
B
B
B B
C
C
C
C
D
D
D
D
1
Removal steps
1.
Fog lamp bezel
2.
Fog lamp assembly
3.
Bulb
4.
Fog lamp
Removal steps (Continued)
Post-installation operation
Check the beam direction of the front fog lamp (Refer to
Front Fog Lamp Aiming
AC801312 AB
1
4
3
2
2.5 ± 0.3 N·m
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст