Mitsubishi L200. Manual — part 499
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-56
REAR PANEL WINDOW REGULATOR
REMOVAL AND INSTALLATION
M1429005800099
Post-installation Operation
• Rear Panel Power Window Glass Adjustment (Refer to
• Rear Panel Power Window Initial Set (Refer to
AC502512
AC505125AB
2
3
4
5
6
8
8
9
9
10
11
7
7
5.0 ± 1.0 N·m
12
13
14
15
16
18
17
A
A
A
A
N
N
N
N
N
N
N
AC505196
AC502679
AC502500
Sealant: 3M ATD Part No. 8625 or equivalent
Sealant: 3M ATD Part No. 3509 or equivalent
2
AC
Section A – A
8
AC901903
1
5
AB
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-57
Rear panel power window switch
removal
1.
Rear panel power window switch
(Refer to GROUP 52A, Centre
lower panel assembly, Instrument
Panel Assembly .)
Rear panel power window
regulator assembly removal
steps
•
Cab rear end lower trim (Refer to
GROUP 52A, Interior Trim .)
>>
B
<<
2.
Waterproof film
<<
A
>>
3.
Rear window panel assembly
4.
Rear window panel
5.
Rear panel power window regulator
6.
Rear panel power window motor
Rear slide window glass and rear
side window glass removal
steps
•
Headlining (Refer to GROUP 52A,
Headlining .)
•
Cab rear end lower trim (Refer to
GROUP 52A, Interior Trim .)
>>
B
<<
2.
Waterproof film
7.
Rear window side moulding
8.
Rear side window glass assembly
9.
Rear body cushion
10. Cab rear window weatherstrip
11. Rear window moulding lower
12. Rear slide window sash side (RH
side)
13. Rear slide window glass
runchannel
14. Rear slide window glass
15. Rear slide window sash side (LH
side)
16. Rear slide window sash upper
>>
A
<<
17. Clip
18. Rear window moulding upper
Post-installation Operation
• Rear Panel Power Window Initial Set (Refer to
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-58
AC502521
19
5.0 ± 1.0 N·m
AB
Rear panel power window-ECU
removal steps
•
Rear pillar trim (Refer to GROUP
52A, Interior Trim .)
19. Rear panel power window-ECU
REAR PANEL POWER WINDOW <Vehicles with rear panel power window>
BODY
42-59
REMOVAL SERVICE POINT
<<A>> REAR WINDOW PANEL ASSEMBLY
REMOVAL
1. Activate the anti-trap function successively 3
times to deactivate the anti-trapping function.
AC502522AB
Rear slide window glass mounting bolts
2. Lower the rear slide window glass until the rear
slide window glass mounting bolts are seen.
3. Remove the rear slide window glass mounting
bolts.
CAUTION
If tinting film is adhered to the rear slide window
glass, attach the special tool, window glass
holder (MB990480) to the outside of the glass to
prevent the film from peeling off.
AC502524AB
MB990480
4. Lift the rear slide window glass, and attach the
special tool, window glass holder (MB990480) to
the glass as shown to prevent the glass from
falling.
5. Remove the rear window panel assembly.
INSTALLATION SERVICE POINTS
>>A<< CLIP INSTALLATION
Since the clip is damaged when the rear slide win-
dow sash upper is removed, replace the clip
(6137A009) and install it to the body.
>>B<< WATERPROOF FILM INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст