Mitsubishi L200. Manual — part 737
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-315
SYMPTOM PROCEDURES
Inspection Procedure 1: No navigation screen is displayed.
CAUTION
Whenever the multivision display is replaced,
ensure that the power supply circuit and the
earthing circuit are normal. (Check that the volt-
age is 10 V or more.)
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-316
COMMENTS ON TROUBLE SYMPTOM
When the ignition switch is turned to the ACC or ON
position, if the screen is not displayed at all, the
power supply circuit or multivision display may have
a problem.
PROBABLE CAUSES
• Malfunction of power supply circuit
• Malfunction of multivision display
Multivision Display Power Source Circuit
IGNITION
SWITCH (ACC)
MULTIVISION DISPLAY
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
FUSIBLE
LINK
20
NOTE
:LHD
:RHD
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-317
DIAGNOSIS PROCEDURE
STEP 1. Connector check: C-167, C-169, C-170
multivision display connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair or replace the damaged connector.
STEP 2. Resistance measurement at C-170
multivision display connector.
(1) Disconnect C-170 multivision display connector,
and measure the resistance available at the
wiring harness side of the connector.
(2) Measure the resistance between C-170
multivision display connector terminal 9 and
earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Go to Step 3.
AC903856AS
Connector: C-167 <LHD>
C-167 (GR)
Harness side
AC903865
Harness side
AJ
Connector: C-167 <RHD>
AC903853
C-169 (GR)
Harness side
AU
Connectors: C-169, C-170 <LHD>
C-170 (GR)
Harness side
C-169
C-170
AC903868
C-169 (GR)
Harness side
BE
Connectors: C-169, C-170 <RHD>
C-170 (GR)
Harness side
C-169
C-170
AC903853
AV
Connector: C-170 <LHD>
C-170 (GR)
Harness side
AC903868
BF
Connector: C-170 <RHD>
C-170 (GR)
Harness side
AC310506KE
Connector C-170
(Harness side)
MITSUBISHI MULTI COMMUNICATION SYSTEM (MMCS)
CHASSIS ELECTRICAL
54A-318
STEP 3. Check the wiring harness between C-170
multivision display connector terminal No.9 and
earth.
• Check the earth wires for open circuit.
NOTE:
Prior to the wiring harness inspection, joint connector
C-120, and repair if necessary.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points, How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness.
STEP 4. Resistance measurement at C-169
multivision display connector.
(1) Disconnect C-169 multivision display connector,
and measure the resistance available at the
wiring harness side of the connector.
(2) Measure the resistance between C-169
multivision display connector terminal 25 and
earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Go to Step 5.
AC903853
AV
Connector: C-170 <LHD>
C-170 (GR)
Harness side
AC903868
BG
Connectors: C-120, C-170 <RHD>
C-120
C-120 (L)
C-170 (GR)
Harness side
C-170
AC903856 AT
Connector: C-120 <LHD>
C-120 (L)
AC903853
C-169 (GR)
Harness side
AW
Connector: C-169 <LHD>
AC903868
C-169 (GR)
Harness side
BH
Connector: C-169 <RHD>
AC310506KF
Connector C-169
(Harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст