Mitsubishi L200. Manual — part 673
COMBINATION METER
CHASSIS ELECTRICAL
54A-59
tool test harness (MB991219) between the wiring
harness connector terminals 1 and 2.
(3) Turn the ignition switch to the "ON" position.
Q: Does the test lamp illuminate?
YES :
Go to Step 7.
NO :
Go to Step 2.
STEP 2. Connector check: Combination meter
connector C-113 and fuel gauge unit connector
F-09.
Q: Is combination meter connector C-113 and fuel
gauge unit connector F-09 in good condition?
YES :
Go to Step 3.
NO :
Repair or replace the damaged
component(s).
STEP 3. Check the wiring harness between
combination meter connector C-113 (terminal 22)
and fuel gauge unit connector F-09 (terminal 1).
Check the input lines for open circuit and short cir-
cuit.
NOTE:
Prior to the wiring harness inspection, check interme-
diate connector C-30 and repair if necessary.
Q: Is the wiring harness between combination meter
connector C-113 (terminal 22) and fuel gauge unit
connector F-09 (terminal 1) in good condition?
AC903856
Harness side
BH
Connector: C-113 <LHD>
AC903868
Harness side
BY
Connector: C-113 <RHD>
AC903957AB
Connector: F-09
Harness side
<Vehicles without
rear body>
AC903856
Connectors: C-30, C-113 <LHD>
BJ
C-30
C-30
C-113
Harness side
C-113
AC903868
Harness side
BY
Connector: C-113 <RHD>
AC903957AB
Connector: F-09
Harness side
<Vehicles without
rear body>
AC903865
Connector: C-30 <RHD>
AN
COMBINATION METER
CHASSIS ELECTRICAL
54A-60
YES :
Go to Step 4.
NO :
Repair or replace the damaged
component(s). Then go to Step 4.
STEP 4. Retest the system.
Q: Is the fuel gauge normal?
YES :
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00 / How to Cope with
Intermittent Malfunction ).
NO :
Go to Step 5.
STEP 5. Check the wiring harness between fuel
gauge unit connector F-09 (terminal 2) and earth.
Check the earth wires for open circuit.
Q: Is the wiring harness between fuel gauge unit
connector F-09 (terminal 2) and earth in good
condition?
YES :
Go to Step 6.
NO :
Repair or replace the damaged
component(s).
STEP 6. Retest the system.
Q: Is the fuel gauge normal?
YES :
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00 / How to Cope with
Intermittent Malfunction ).
NO :
Carry out the troubleshooting again.
STEP 7. Check the fuel gauge unit.
Refer to
Q: Is the fuel gauge normal?
YES :
Go to Step 8.
NO :
Replace the fuel gauge unit.
STEP 8. Retest the system.
Q: Is the fuel gauge normal?
YES :
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00 / How to Cope with
Intermittent Malfunction ).
NO :
Replace combination meter.
AC903957AB
Connector: F-09
Harness side
<Vehicles without
rear body>
COMBINATION METER
CHASSIS ELECTRICAL
54A-61
Inspection Procedure 8: Engine coolant temperature gauge does not work (Other meters work).
COMMENTS ON TROUBLE SYMPTOM
If only the engine coolant temperature gauge does
not operate, the engine ECU system, the combina-
tion meter, the wiring harness or its connector may
be defective.
PROBABLE CAUSES
• Damaged harness wires and connectors
• Malfunction of the engine coolant temperature
gauge unit
• Malfunction of combination meter
DIAGNOSIS PROCEDURE
STEP 1. Check the engine coolant temperature
gauge circuit.
(1) Disconnect the A-108 engine coolant
temperature gauge unit connector.
(2) Connect a test lamp (12 V
− 3.4 W to 12 V − 7.0
W) to the wiring harness side connector.
(3) Ignition switch: ON
Q: Does the test lamp illuminate?
YES :
Go to Step 5.
NO :
Go to Step 2.
Engine Coolant Temperature Gauge Circuit
ENGINE COOLANT
TEMPERATURE
GAUGE UNIT
COMBINATION
METER
T/GA
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Grey R : Red P : Pink V : Violet PU : Purple SI : Silver
NOTE
: LHD
: RHD
AC903898
AC
Connector: A-108
Harness side
A-108 (B)
AC503028AC
Connector
Earth
Test lamp
(12 V 3.4 W - 7.0 W)
Engine coolant
temperature gauge unit
COMBINATION METER
CHASSIS ELECTRICAL
54A-62
STEP 2. Connector check: Combination meter
connector C-113 and engine coolant temperature
gauge unit connector A-108.
Q: Is combination meter connector C-113 and engine
coolant temperature gauge unit connector A-108 in
good condition?
YES :
Go to Step 3.
NO :
Repair or replace the damage
component(s).
STEP 3. Retest the system.
Q: Is the engine coolant temperature gauge normal?
YES :
The procedure is complete. (If no
malfunctions are found in all steps, an
intermittent malfunction is suspected. Refer
to GROUP 00 / How to Cope with
Intermittent Malfunction ).
NO :
Go to Step 4.
AC903898
AC
Connector: A-108
Harness side
A-108 (B)
AC903856
Harness side
BH
Connector: C-113 <LHD>
AC903868
Harness side
BY
Connector: C-113 <RHD>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст