Mitsubishi L200. Manual — part 789
ETACS
CHASSIS ELECTRICAL
54A-523
• Malfunction of the ETACS-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III diagnosis code.
When the ignition switch is turned to the "LOCK"
(OFF) position, check that the ETACS-ECU does not
set the diagnosis code.
Q: Is the diagnosis code set?
YES :
Refer to diagnosis code chart
.
NO :
Go to Step 2.
STEP 2. Connector check: C-302 column switch
connector
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Repair the defective connector.
STEP 3. Resistance measurement at the C-302
column switch connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Check the resistance between C-302 column
switch connector terminal No.4 and body earth.
OK: Continuity exists (2
Ω or less)
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC310507
Connector C-302
(Harness side)
MA
ETACS
CHASSIS ELECTRICAL
54A-524
STEP 4. Check the wiring harness from C-302
column switch connector terminal No.4 to body
earth.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness.
STEP 5. Voltage measurement at C-302 column
switch connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Voltage between C-302 column switch connector
No.1 and body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Go to Step 6.
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC310507
Connector C-302
(Harness side)
MA
ETACS
CHASSIS ELECTRICAL
54A-525
STEP 6. Check the wiring harness between C-302
column switch connector terminal No.1 and
fusible link (20).
NOTE:
Prior to the wiring harness inspection, check junction
block connectors C-209, C-213 and joint connector
C-132, and repair if necessary.
• Check the power supply line for open circuit and
short circuit.
Q: Is the check result normal?
AC503086
AD
Battery
Front of vehicle
24
23
22
21
20
19
Fusible link (20)
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC903853
Connector: C-132 <LHD>
AC
C-132 (GR)
AC903865
Connector: C-132 <RHD>
AB
C-132 (GR)
AC509934
Connectors: C-209, C-213 <LHD>
Junction block (Front view)
C-213
C-209
C-213
C-209
AC
Harness side
Harness side
AC509936
Connectors: C-209, C-213 <RHD>
C-213
C-209
AC
Junction block
(Front view)
C-213
C-209
Harness side Harness side
ETACS
CHASSIS ELECTRICAL
54A-526
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction ).
NO :
Repair the wiring harness.
STEP 7. Voltage measurement at C-302 column
switch connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Voltage between C-302 column switch connector
No.9 and body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Go to Step 8.
AC903858 AJ
Harness side
Connector: C-302 <LHD>
AC903869AJ
Harness side
Connector: C-302 <RHD>
AC310507
Connector C-302
(Harness side)
MB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст