Mitsubishi L200. Manual — part 277
AC103525
SPECIAL TOOLS
AUTOMATIC TRANSMISSION
23A-15
MD998330
(including
MD998331)
Oil pressure gauge (3.0
MPa)
Hydraulic pressure measurement
MD998332
Adapter
Oil pressure gauge connection
MD998900
Joint
Tool
Number
Name
Use
TROUBLESHOOTING
AUTOMATIC TRANSMISSION
23A-16
TROUBLESHOOTING
DIAGNOSIS TROUBLESHOOTING FLOW
M1231104000153
Ask about trouble symptoms
Check the A/T fluid
Check the trouble symptoms
Replace the A/T fluid
To INSPECTION CHART FOR
TROUBLE SYMPTOMS
Reading of a diagnosis code
Erase of a diagnosis code
Check the trouble symptoms
Inhibitor switch, TPS check
Road test
Recheck diagnosis codes
To INSPECTION CHART FOR
DIAGNOSIS CODES
To INSPECTION CHART FOR
TROUBLE SYMPTOMS
Check for the cause
Repair
Confirmation test (road test)
INTERMITTENT MALFUNCTIONS
(Refer to GROUP 00 - Points to
Note for Intermittent Malfunction)
Completed
NG
OK
Communication with the
MUT-II not possible
Diagnosis code output
exists
No diagnosis code output
Abnormality exists (no diagnosis code output)
Abnormality exists
(diagnostic trouble
code output)
No abnormality
Found
Not found
OK
OK
NG
AC212495
NG
Diagnosis code output
exists
No diagnosis code output
Communication with the
M.U.T.-III not possible
AD
Perform the repair
DIAGNOSTIC FUNCTION
M1231103300151
SELECTOR LEVER POSITION INDICATOR
LAMP SYSTEM
AC504108AB
If there is a problem with any of the A/T system, the
selector lever position indicator lamp will flash at a
rate of approximately once per second.
If the selector lever position indicator lamp is flashing
at a rate of approximately once per second, check
the diagnosis output.
Selector lever position indicator lamp flashing
item
• Input shaft speed sensor system
• Output shaft speed sensor system
• Solenoid valves system
• Non-synchronization at various shift ranges
• A/T control relay system
TROUBLESHOOTING
AUTOMATIC TRANSMISSION
23A-17
NOTE: If the A/T fluid temperature warning lamp is
illuminating, the A/T fluid temperature is high. (It illu-
minates when the fluid is approximately 135
°
C or
more and goes off when the fluid is approximately
115
°
C or less.)
METHOD OF READING THE DIAGNOSIS
CODE
Use the M.U.T.-III to read the diagnosis code. (Refer
to GROUP 00
− How to Use Troubleshooting/Inspec-
tion Service Points .)
METHOD OF ERASING THE DIAGNOSIS
CODE
Use the M.U.T.-III to erase the diagnosis code.
(Refer to GROUP 00
− How to Use Troubleshooting/
Inspection Service Points .)
ROAD TEST
M1231100800500
Proced
ure
Pre-test/
operation
conditions
Test/operation
Judgment value
Check
item
Diagnosi
s code
No.
Inspection
procedure if
there is an
abnormality
1
Ignition switch:
LOCK (OFF)
position
Ignition switch
(1) ON
Data List No.8
(1) System voltage
[V]
A/T
control
relay
P1788
A/T control
relay system
TROUBLESHOOTING
AUTOMATIC TRANSMISSION
23A-18
2
Ignition switch:
ON
Engine:
Stopped
Selector lever
position: P
Selector lever
position <4A/T>
(1) P
(2) R
(3) N
(4) D
(5) 2
(6) L
Data List No.34
(1) P
(2) R
(3) N
(4) D
(5) 2
(6) L
Inhibitor
switch
P1770,
P1771
Inhibitor switch
system
Selector lever
position <5A/T>
(1) P
(2) R
(3) N
(4) D
Data List No.34
(1) P
(2) R
(3) N
(4) D
Selector lever
position <5A/T>
(1) D
(2) Select the sport
mode
(3) Upshift and hold
the selector lever
in that position
(2nd gear)
(4) Downshift and
hold the selector
lever in that
position (1st
gear)
Data List No.27
(1) OFF
(2) ON
(3) ON
(4) ON
Select
switch
−
Sport mode
switch system
Data List No.28
(1) OFF
(2) OFF
(3) ON
(4) OFF
Upshift
switch
Data List No.29
(1) OFF
(2) OFF
(3) OFF
(4) ON
Downshift
switch
Shift indicator lamp
(1) Only D
illuminates
(2) Only 1
illuminates
(3) Only 2
illuminates
(4) Only 1
illuminates
Shift
indicator
lamp
Overdrive switch
<4A/T>
(1) ON
(2) OFF
Data List No.26
(1) ON
(2) OFF
Overdrive
switch
−
Overdrive
switch system
Accelerator pedal
(1) Fully closed
(2) Depressed
(3) Fully opened
Data List No.35
(1) 0%
(2) Gradually
increases from (1)
(3) 100%
APS
−
Refer to
GROUP 13A
−
Troubleshootin
g.
Transfer shift lever
position
(1) Except for 4L
Data List No.31
(1) OFF
(2) ON
4LLc
switch
−
4LLc switch
system
Proced
ure
Pre-test/
operation
conditions
Test/operation
Judgment value
Check
item
Diagnosi
s code
No.
Inspection
procedure if
there is an
abnormality
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст